RADIO ANTENNA CORD REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B004QZ9

Click here

PROCEDURE


  1. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  2. REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)

    Click here

  3. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

    Click here

  4. REMOVE NO. 2 KNEE PROTECTOR BRACKET (for LHD)

    Click here

  5. REMOVE NO. 3 KNEE PROTECTOR BRACKET (for LHD)

    Click here

  6. REMOVE ANTENNA CORD SUB-ASSEMBLY


    1. for LHD:


      1. Disengage the 6 clamps and remove the antenna cord sub-assembly.

        B004OUF

    2. for RHD:


      1. Disengage the 4 clamps and remove the antenna cord sub-assembly.

        B004QHR

  7. REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)


    1. w/ Navigation Antenna:


      1. Disengage the 6 clamps and remove the antenna cord sub-assembly.

        B004PY9

  8. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  9. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. w/o Digital Audio Broadcasting Antenna or Television Antenna:


      1. Remove the adhesive tape from the roof headlining assembly.

        B004QO8C02
        *A w/o Sliding Roof *B w/ Sliding Roof
        B004PFI Adhesive Tape B004P9H Front

    2. w/ Digital Audio Broadcasting Antenna or Television Antenna:


      1. Disengage each clamp.

        B004QXGC01
        *A w/o Sliding Roof *B w/ Sliding Roof
        B004PFI Adhesive Tape B004P9H Front

      2. Remove the adhesive tape from the roof headlining assembly.

    3. Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.

  10. REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY


    1. w/ Digital Audio Broadcasting Antenna or Television Antenna:


      1. B004P16

        Disconnect the connector.

      2. Disengage the clamp and remove the No. 5 antenna cord sub-assembly.

  11. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. B004QL9

      Disconnect the connector.

    2. Disengage the claw.

    3. Disengage the 6 clamps and remove the No. 3 antenna cord sub-assembly.

  12. REMOVE BACK DOOR UPPER TRIM PANEL ASSEMBLY

    Click here

  13. REMOVE BACK DOOR SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  14. REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY


    1. B004QXD

      Disconnect the connector.

    2. Disconnect the washer hose.

      Tech Tips

      Use a container to collect the windshield washer fluid.

    3. Disengage the 3 clamps.

    4. B004QAT

      Disconnect the connector.

    5. Disconnect the washer hose.

      Tech Tips

      Use a container to collect the windshield washer fluid.

    6. Disengage the clamp.

    7. B004Q5H

      Disengage the 8 claws to separate the 2 grommets.

      Note

      When reusing the No. 4 antenna cord sub-assembly, make sure to replace the No. 1 wire harness protector and No. 2 wire harness protector with new ones as reusing them may cause water ingress.

    8. Remove the No. 4 antenna cord sub-assembly.

    9. When reusing the No. 4 antenna cord sub-assembly:


      1. for Back Door Side:


        1. B004OTCC02
          *a Antenna Cord
          *b Washer Hose
          B004PFI Tape

          Remove the tape to disconnect the antenna cord and washer hose from the No. 2 wire harness protector.

        2. B004PB2C02
          B004PFI Tape

          Remove the tape to disconnect the rubber protrusion of the grommet from the No. 2 wire harness protector.

      2. B004QN0C02
        B004PI4 Remove in this Direction

        Separate the No. 1 wire harness protector from the grommet as shown in the illustration.

        Tech Tips

        Use the same procedure for the No. 2 wire harness protector.

      3. B004OIRC02
        B004PI4 Remove in this Direction

        Disengage the claw as shown in the illustration and remove the No. 1 wire harness protector.

        Tech Tips

        Use the same procedure for the No. 2 wire harness protector.