FRONT AXLE HUB INSTALLATION

CAUTION / NOTICE / HINT

Note


  • When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT AXLE HUB SUB-ASSEMBLY


    1. Secure the steering knuckle between aluminum plates in a vise.

      Note

      Do not overtighten the vise.

    2. Install the front axle hub sub-assembly and front disc brake dust cover to the steering knuckle with the 3 bolts.

      Torque:
      130 N*m  { 1326 kgf*cm, 96 ft.*lbf }

      Note


      • Be careful not to damage the speed sensor rotor or contact surfaces.

      • Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.

  2. INSTALL FRONT AXLE ASSEMBLY


    1. A01VBRRC02
      B004PRK Toyota Body Grease W

      Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.

    2. Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

      Torque:
      240 N*m  { 2447 kgf*cm, 177 ft.*lbf }

      Note


      • Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.

      • When installing the nuts, keep the bolts from rotating.

      Tech Tips

      The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.

  3. INSTALL FRONT DRIVE SHAFT ASSEMBLY


    1. A01VDDKC03
      *a Matchmark

      Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and connect the front drive shaft assembly to the front axle assembly.

      Note


      • Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

      • Check that there is no foreign matter on the speed sensor rotor or contact surfaces.

      • Do not damage the front drive shaft outboard joint boot.

      • Do not damage the front disc brake dust cover.

      • Do not damage the speed sensor rotor.

  4. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY


    1. Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

      Torque:
      89 N*m  { 908 kgf*cm, 66 ft.*lbf }

  5. CONNECT TIE ROD END SUB-ASSEMBLY

    Click here

  6. INSTALL FRONT DISC

    Click here

  7. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

    Click here

  8. INSTALL FRONT AXLE SHAFT NUT


    1. Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

      Note


      • Be sure to perform this work even when using a new front drive shaft assembly.

      • Keep the threaded parts free of oil and foreign matter.

    2. Using a 30 mm deep socket wrench, while applying the brakes, temporarily install the front axle shaft nut.

      Torque:
      216 N*m  { 2203 kgf*cm, 159 ft.*lbf }

      Note

      Stake the front axle shaft nut after inspecting for looseness and runout in the following steps.

      Tech Tips

      Keep depressing the brake pedal to prevent the front drive shaft from rotating.

  9. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

    Click here

  10. REMOVE FRONT DISC

    Click here

  11. INSPECT FRONT AXLE HUB BEARING LOOSENESS

    Click here

  12. INSPECT FRONT AXLE HUB RUNOUT

    Click here

  13. INSTALL FRONT DISC

    Click here

  14. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

    Click here

  15. INSTALL FRONT SPEED SENSOR


    1. A01VCAVC02
      B004PRK Hook

      Set the 2 hooks of front speed sensor to the front shock absorber assembly.

      Note

      Do not twist the front speed sensor when installing it.

    2. A01VCMT

      Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

      Note

      Do not twist the front flexible hose when installing it.

    3. A01VD4U

      Install the front speed sensor to the steering knuckle with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Prevent foreign matter from attaching to the front speed sensor tip.

      • Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.

      • After installing the front speed sensor to the steering knuckle, make sure that there is no clearance between the front speed sensor stay and steering knuckle. Also make sure that no foreign matter is stuck between the parts.

      • Do not twist the front speed sensor when installing it.

    4. Engage the clamp.

      Note

      Do not twist the front speed sensor when installing it.

  16. STAKE FRONT AXLE SHAFT NUT


    1. A01VCVA

      Using a chisel and hammer, stake the front axle shaft nut.

  17. INSTALL FRONT WHEEL

    Click here

  18. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Connect the reservoir level switch connector.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

      Click here

    3. Turn the power switch on (READY).

    4. Depress the brake pedal and release it.

    5. Clear the DTCs.

      Click here

  19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  20. CHECK FOR SPEED SENSOR SIGNAL

    Click here