FUEL PUMP(w/o Canister Pump Module) INSTALLATION

PROCEDURE


  1. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    1. Install a new fuel suction tube set gasket to the fuel tank assembly.

    2. Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

      Note

      Be careful not to bend the arm of the fuel sender gauge assembly.

    3. A01VBFIC02
      *a Protrusion
      B004PRK Notch

      Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.

  2. INSTALL FUEL PUMP GAUGE RETAINER


    1. Install the fuel pump gauge retainer.


      1. While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.

      2. A01VBWQC03
        *a Insertion Point
        *b SST (Plate)
        *c SST (Claw)
        *d SST (Bolt)

        Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

        SST
        09808-14030   ( 09808-01030, 09808-01050 )
        09808-01071

        Tech Tips

        Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.

      3. While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).

      4. A01VCFMC02
        *a Triangle Mark (Fuel Pump Gauge Retainer)
        *b Triangle Mark (Fuel Tank Assembly)
        *c SST (Handle)
        *d SST (Plate)
        *e SST (Claw)
        *f SST (Bolt)
        B004P9H Front Side

        Install SST (handle) to SST (plate).

        SST
        09808-14030   ( 09808-01010, 09808-01030, 09808-01050 )
        09808-01071

      5. Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer are aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

        Note


        • Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

        • Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

        • Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

        • Do not spin SST too fast or use an impact wrench as this may result in damage to components.

        • If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

        • Make sure that the fuel suction tube set gasket does not come off.

    2. Engage the claw to install the No. 1 fuel tube clamp.

  3. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

      A01VDAEC02
      *1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
      *3 Fuel Tank Main Tube Sub-assembly - -
      *a Fuel Tube Joint *b O-ring
      *c Correct *d Incorrect
      *e Collar - -
      B004PRK Insert B004P9H Insert

      Note


      • Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

      • Check that the fuel tube joint is securely inserted to the end.

      • Check that the tube joint clip is on the collar of the fuel tube joint as shown in the illustration.

      • After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.

  4. CONNECT CHARCOAL CANISTER OUTLET HOSE


    1. Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly.

  5. CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A01VD2CC02
      *a Up
      *b 120°

      Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.

      Tech Tips

      Engage the clip within the area shown in the illustration.

  6. INSTALL REAR FLOOR SERVICE HOLE COVER


    1. Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.

    2. Clean the installation surfaces of the rear floor service hole cover and vehicle body.

    3. Connect the fuel pump connector.

    4. Install the rear floor service hole cover with new butyl tape.

  7. INSTALL NO. 3 WIRING HARNESS PROTECTOR


    1. Install a new No. 3 wiring harness protector to the rear floor service hole cover.

  8. INSTALL CENTER REAR SEATBACK HINGE SUB-ASSEMBLY


    1. Install the center rear seatback hinge sub-assembly to the vehicle body with the 2 bolts.

      Torque:
      36.8 N*m  { 375 kgf*cm, 27 ft.*lbf }

  9. INSTALL NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

    Click here

  10. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  11. INSPECT FOR FUEL LEAK

    Click here

  12. INSTALL REAR SEAT ASSEMBLY

    Click here

  13. INSTALL DECK FLOOR BOX RH (w/o Spare Tire)

    Click here

  14. INSTALL DECK FLOOR BOX LH (w/o Spare Tire)

    Click here

  15. INSTALL DECK FLOOR BOX RH (w/ Compact Spare Tire)

    Click here

  16. INSTALL DECK FLOOR BOX LH (w/ Compact Spare Tire)

    Click here

  17. INSTALL REAR DECK FLOOR BOX (w/ Compact Spare Tire)

    Click here

  18. INSTALL DECK FLOOR BOX LH (w/ Full Size Spare Tire)

    Click here

  19. INSTALL DECK FLOOR BOX RH (w/ Full Size Spare Tire)

    Click here

  20. INSTALL DECK BOARD RETAINER

    Click here

  21. INSTALL REAR NO. 1 FLOOR BOARD

    Click here

  22. PERFORM INITIALIZATION


    1. Perform "Inspection After Repair" after replacing the fuel pump with filter assembly.

      Click here