ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | except Rough Road Area Specification Vehicles | *B | for Rough Road Area Specification Vehicles |
| *1 | AIR CLEANER BRACKET | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | RADIATOR SUPPORT OPENING COVER |
| *5 | INLET NO. 1 AIR CLEANER | *6 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *7 | NO. 1 ENGINE UNDER COVER | *8 | NO. 2 ENGINE UNDER COVER |
| *9 | INLET NO. 2 AIR CLEANER | *10 | REAR MOTOR UNDER COVER LH |
| *11 | REAR MOTOR UNDER COVER RH | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Exhaust Heat Recirculation System | *B | w/o Exhaust Heat Recirculation System |
| *1 | FUEL TUBE SUB-ASSEMBLY | *2 | INLET HEATER WATER HOSE A |
| *3 | OUTLET HEATER WATER HOSE E | *4 | INLET HYBRID RADIATOR HOSE |
| *5 | NO. 1 FUEL VAPOR FEED HOSE | *6 | OUTLET NO. 1 HYBRID WATER PUMP HOSE |
| *7 | NO. 3 RADIATOR HOSE | *8 | NO. 2 RADIATOR HOSE |
| *9 | NO. 8 WATER BY-PASS HOSE | *10 | FUEL PIPE |
| *11 | NO. 1 FUEL PIPE CLAMP | *12 | NO. 3 ENGINE WIRE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT FLOOR COVER LH | *2 | FRONT FLOOR COVER RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Exhaust Heat Recirculation System | *B | w/o Exhaust Heat Recirculation System |
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | COMPRESSOR WITH MOTOR ASSEMBLY |
| *3 | FRONT AXLE SHAFT NUT LH | *4 | FRONT CENTER FLOOR BRACE |
| *5 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) | *6 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
| *7 | FRONT SPEED SENSOR LH | *8 | FRONT STABILIZER LINK ASSEMBLY LH |
| *9 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *10 | TIE ROD END SUB-ASSEMBLY LH |
| *11 | EXHAUST PIPE GASKET | *12 | COMPRESSION SPRING |
| *13 | BRACKET | *14 | EXHAUST PIPE SUPPORT |
| *15 | OUTLET HEATER WATER HOSE C | *16 | OUTLET HEATER WATER HOSE B |
| *17 | COTTER PIN | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *A | except Rough Road Area Specification Vehicles | *B | for Rough Road Area Specification Vehicles |
| *1 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH | *2 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
| *3 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | *4 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
| *3 | ENGINE WIRE | *4 | AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
| *5 | ENGINE ASSEMBLY WITH TRANSAXLE | *6 | WIRE HARNESS CLAMP BRACKET |
| *7 | COOLER BRACKET | *8 | NO. 2 EARTH WIRE |
| *9 | NO. 2 ENGINE MOUNTING STAY LH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque |  |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY | *2 | FLYWHEEL HOUSING SIDE COVER |
| *3 | FLYWHEEL SUB-ASSEMBLY | *4 | FRONT DRIVE SHAFT ASSEMBLY LH |
| *5 | FRONT DRIVE SHAFT ASSEMBLY RH | *6 | FRONT DRIVE SHAFT HOLE SNAP RING |
| *7 | HYBRID VEHICLE TRANSAXLE ASSEMBLY | *8 | STARTER HOLE INSULATOR |
| *9 | TRANSMISSION INPUT DAMPER ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Do not apply lubricants to the threaded parts | |
Adhesive 1324 |
 |
ATF WS | ★ | Precoated part |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° |
- | - |