SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P319300

DTC Code DTC Name
P319300 Fuel Run Out

DESCRIPTION

The ECM receives the low fuel level signal from the combination meter assembly (meter ECU) to detect if the vehicle is running out of fuel.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P319300 Fuel Run Out

All of the following conditions are met (1 trip detection logic):


  1. Power switch on (IG).

  2. The ECM receives the fuel empty low level signal from the combination meter assembly (meter ECU).

  3. DTC detection conditions of either DTC P319000 or P319100 are met.

 - (This DTC indicates that the vehicle ran out of fuel and does not indicate the malfunction of part.) Does not come on DTC stored SAE Code: P3193

MONITOR DESCRIPTION

This DTC indicates that the vehicle ran out of fuel. If the ECM receives the low fuel level signal from the combination meter assembly (meter ECU) and the DTC detection conditions of either DTC P319000 or P319100 are met while the power switch is on (IG) or the engine is operating, the ECM stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

Note

If the MIL or a warning light illuminates, immediately end the confirmation driving pattern. When DTCs P319000, P319100 and P319300 are output, the engine may stop. In this case, the HV battery will no longer be chargeable and the distance that the vehicle can be driven will be limited.

B004QX9E26
*1 40 km/h [Engine running]
*2 Power Switch on (READY)
*3 Total engine operation time of 10 minutes or more

  1. Apply the parking brake firmly.

  2. Connect the GTS to the DLC3.

  3. Turn the power switch on (IG).

  4. Turn the GTS on.

  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  6. Turn the power switch off and wait for at least 30 seconds.

  7. Turn the power switch on (READY).

  8. Turn the GTS on.

  9. Fully depress the accelerator pedal for 10 seconds with the vehicle stopped, park (P) selected and the brake pedal depressed [A].

    Note

    As soon as the engine starts, release the accelerator pedal.

  10. Release the parking brake.

  11. Drive the vehicle at an average of approximately 40 km/h (25 mph) or more until the total engine operation time is 10 minutes or more [B].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips


    • It is not necessary to maintain the vehicle speed at 40 km/h (25 mph) throughout the road test.

    • If the engine stops, further depress the accelerator pedal to restart the engine.

  12. Enter the following menus: Powertrain / Engine / Trouble Codes [C].

  13. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  15. Input the DTC: P319300.

  16. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips

    If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

CAUTION / NOTICE / HINT

Note


  • Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here

Tech Tips


  • When DTCs P319000, P319100 and P319300 are output, the engine may stop.

    In this case, after adding fuel or performing repairs, clear the DTCs. Then turn the power switch off to return to the normal condition.

  • When this DTC is output and the engine is stopped, the HV battery cannot be charged since the vehicle is driven with the motor only. If the vehicle continues to be driven under this condition, the HV battery will become depleted and the power switch will not be able to be turned on (READY).

PROCEDURE


  1. CHECK SHORTAGE OF FUEL


    1. Check the amount of fuel remaining.

      OK
      There is enough fuel.

      Tech Tips


      • DTCs P319000, P319100 and/or P319300 may be output if the vehicle ran out of fuel in the past.

      • If not enough fuel is added, DTC P319000, P319100 or P319300 may be output again. If the engine cannot be started because the vehicle is out of fuel, add fuel until the fuel level warning turns off.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 3 Click here

    NG

  2. REFILL FUEL


    1. Add fuel until the fuel level warning turns off.

      Result
      Proceed to
      NEXT

    NEXT

  3. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the power switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK WHETHER DTC OUTPUT RECURS


    1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    2. Enter the following menus: Powertrain / Engine / Trouble Codes.

    3. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P319000 or P319100 is output B
      DTC P319000 or P319100 and other DTCs are output C

    A

    END

    B

    GO TO DTC P319000, P319100 Click here

    C

    GO TO DTC CHART Click here