SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P106A62

DTC Code DTC Name
P106A62 Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure

DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P106A62 Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and manifold absolute pressure sensor (Intake Manifold Absolute Pressure*) is higher than 8.69 kPa (1.26 psi) (2 trip detection logic).

  • Canister pressure sensor (canister pump module)

  • Manifold absolute pressure sensor

 Comes on DTC stored SAE Code: P106A

Tech Tips

*: Data List name

MONITOR DESCRIPTION

This DTC is designed to detect a deviation in the output characteristics of a pressure sensor.

The pressure of the canister pressure sensor and manifold absolute pressure sensor is monitored 50 minutes after the power switch is turned off. If there is a difference in the pressures, the ECM determines there is a malfunction, illuminates the MIL and stores a DTC.

Tech Tips

Correct judgment may not be possible when the altitude is 4000 m (13124 ft.) or higher.

MONITOR STRATEGY

Required Sensors/Components

Canister pressure sensor

Manifold absolute pressure sensor
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the power switch off and wait for at least 30 seconds.

  6. Turn the power switch on (IG).

  7. Turn the GTS on.

  8. Put the engine in Inspection Mode (Maintenance Mode).

    Click here

  9. Start the engine and idle for 10 seconds or more [A].

  10. Turn the power switch off.

  11. Leave the power switch off for 55 minutes [B].

  12. Turn the power switch on (IG).

  13. Turn the GTS on.

  14. Enter the following menus: Powertrain / Engine / Trouble Codes [C].

  15. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  17. Input the DTC: P106A62.

  18. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE or N/A, perform steps [A] through [C] again.

CAUTION / NOTICE / HINT

Tech Tips


  • Refer to "Data List / Active Test" [Intake Manifold Absolute Pressure and Vapor Pressure Pump].

    Click here

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P106A62)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P106A62 is output A
      DTC P106A62 and other DTCs are output B

      Tech Tips

      If any DTCs other than P106A62 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE AND VAPOR PRESSURE PUMP)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure and Vapor Pressure Pump.


      Powertrain > Engine > Data List
      Tester Display
      Intake Manifold Absolute Pressure
      Vapor Pressure Pump

    5. Compare the Intake Manifold Absolute Pressure and Vapor Pressure Pump data from the Data List with day's atmospheric pressure*. Read the Data List twice, when the engine is both cold and warmed up.

      Tech Tips


      • *: Standard atmospheric pressure is 101 kPa(abs) [15 psi(abs)]. For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (0.1 psi). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).

      • Also, check Atmosphere Pressure in the Data List.

      • If you do not know the atmospheric pressure, check the value of Vapor Pressure Pump output by other vehicles in the workshop and check the difference in pressure.

      Result
      Result Proceed to
      The difference between the value of Vapor Pressure Pump and atmospheric pressure is 3.5 kPa or more A
      The difference between the value of Intake Manifold Absolute Pressure and atmospheric pressure is 3.5 kPa or more B

      Tech Tips

      3.5 kPa = 0.5 psi


    B

    REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR Click here

    A

  3. REPLACE CANISTER PUMP MODULE


    1. Replace the canister pump module.

      Tech Tips

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 5 Click here

  4. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR


    1. Replace the manifold absolute pressure sensor.

      Tech Tips

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure and Vapor Pressure Pump.


      Powertrain > Engine > Data List
      Tester Display
      Intake Manifold Absolute Pressure
      Vapor Pressure Pump

    5. Confirm that the difference between Intake Manifold Absolute Pressure and Vapor Pressure Pump are 3.5 kPa (0.5 psi) or less.

      Result
      Proceed to
      NEXT

    NEXT

    END