SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P010014, P010016

DTC Code DTC Name
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open
P010016 Mass or Volume Air Flow Sensor "A" Circuit Voltage Below Threshold

DESCRIPTION

Refer to DTC P010012.

Click here

Tech Tips

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open

Both of the following conditions are met for 3 seconds or more: (1 trip detection logic)


  • The mass air flow meter sub-assembly voltage is less than 0.2 V.

  • The engine speed is less than 4000 rpm.

  • Open or short in mass air flow meter sub-assembly circuit

  • Mass air flow meter sub-assembly

  • ECM

 Comes on DTC stored SAE Code: P0102
P010016 Mass or Volume Air Flow Sensor "A" Circuit Voltage Below Threshold

Both of the following conditions are met for 3 seconds or more: (2 trip detection logic)


  • The mass air flow meter sub-assembly voltage is less than 0.2 V.

  • The engine speed is 4000 rpm or higher.

  • Open or short in mass air flow meter sub-assembly circuit

  • Mass air flow meter sub-assembly

  • ECM

 Comes on DTC stored SAE Code: P0102

Tech Tips

When these DTCs are output, check the mass air flow rate in the Data List. Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

DTC No. Mass Air Flow Sensor Malfunction

P010014

P010016

 0 gm/sec

  • Open in mass air flow meter sub-assembly power source circuit

  • Open in VG circuit

  • Short to ground in VG circuit

If the Data List value is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

MONITOR DESCRIPTION

If the mass air flow meter sub-assembly is malfunctioning or there is an open or short in the mass air flow meter sub-assembly circuit, the voltage will deviate from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit, illuminate the MIL and stores a DTC.

Example:

When the sensor output voltage remains less than 0.2 V for 3 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

B004P8VE11

  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the power switch off and wait for at least 30 seconds.

  6. Turn the power switch on (IG) [A].

  7. Turn the GTS on.

  8. Put the engine in Inspection Mode (Maintenance Mode).

    Click here

  9. Start the engine.

  10. Idle the engine for 5 seconds [B].

  11. Enter the following menus: Powertrain / Engine / Trouble Codes [C].

  12. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  13. With the engine running, during normal driving, increase the vehicle speed to 80 km/h (50 mph) [D].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips

    If the engine stops, further depress the accelerator pedal to restart the engine.

  14. With the engine running, depress the accelerator pedal fully to increase the vehicle speed to between 100 and 120 km/h (62 and 75 mph) (engine speed of 4000 rpm or more) and maintain the speed for at least 5 seconds [E].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips

    If the engine stops, further depress the accelerator pedal to restart the engine.

  15. Enter the following menus: Powertrain / Engine / Trouble Codes [F].

  16. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  18. Input the DTC: P010014 or P010016.

  19. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE or N/A, perform steps [B] through [F] again.

WIRING DIAGRAM

Refer to DTC P010012.

Click here

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)

    Tech Tips

    Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


    1. Disconnect the mass air flow meter sub-assembly connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      C5-1 (+B) - Body ground Power switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - MASS AIR FLOW METER SUB-ASSEMBLY)

    OK

  2. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)


    1. Disconnect the mass air flow meter sub-assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C5-3 (VG) - C31-137 (VG) Always Below 1 Ω
      C5-3 (VG) or C31-137 (VG) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)


    1. Disconnect the mass air flow meter sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C5-3 (VG) - C5-2 (E2G) Power switch off 190 to 210 kΩ

      Tech Tips

      Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MASS AIR FLOW METER SUB-ASSEMBLY Click here

    NG

    REPLACE ECM Click here