FORWARD RECOGNITION CAMERA SYSTEM TERMINALS OF ECU


  1. CHECK FORWARD RECOGNITION CAMERA

    Note


    • DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

    • Do not apply excessive force to the O7 forward recognition camera connector.

    A003PGSE48

    1. Disconnect the O7 forward recognition camera connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      O7-7 (IGB) - O7-10 (GND) LG - W-B Power source Power switch on (IG) 11 to 14 V
      Power switch off Below 1 V
      O7-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

    3. Reconnect the O7 forward recognition camera connector.

    4. w/ Forward recognition with heater hood sub-assembly:

      Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      O7-1 (HTR) - O7-10 (GND) BE - W-B Forward recognition with heater hood sub-assembly operation signal

      Power switch on (IG)

      Forward recognition with heater hood sub-assembly not operating

      		 11 to 14 V

      Power switch on (IG)

      Forward recognition with heater hood sub-assembly operating

      		 Below 1 V

    5. Check for pulses according to the value(s) in the table below.

      Tech Tips

      If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      O7-5 (CA1P) - O7-10 (GND) GR - W-B CAN communication signal Power switch on (IG)

      Pulse generation

      (See waveform 1)
      O7-11 (CA1N) - O7-10 (GND) W - W-B CAN communication signal Power switch on (IG)

      Pulse generation

      (See waveform 2)
      O7-6 (CANH) - O7-10 (GND) G - W-B CAN communication signal Power switch on (IG)

      Pulse generation

      (See waveform 1)
      O7-12 (CANL) - O7-10 (GND) W - W-B CAN communication signal Power switch on (IG)

      Pulse generation

      (See waveform 2)

      1. A003PJLE97
        *a 1 V/DIV.
        *b 10 μsec./DIV.

        WAVEFORM 1

        Item Content
        Terminal Name

        Between O7-5 (CA1P) and O7-10 (GND)

        Between O7-6 (CANH) and O7-10 (GND)
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Power switch on (IG)

        Tech Tips

        The waveform varies depending on the CAN communication signal.

      2. A003PJ4E89
        *a 1 V/DIV.
        *b 10 μsec./DIV.

        WAVEFORM 2

        Item Content
        Terminal Name

        Between O7-11 (CA1N) and O7-10 (GND)

        Between O7-12 (CANL) and O7-10 (GND)
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Power switch on (IG)

        Tech Tips

        The waveform varies depending on the CAN communication signal.