ROOF RACK REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL NO. 2 ROOF CARRIER PROTECTOR


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the No. 2 roof carrier protector.


      1. Remove the peeling paper from the face of the No. 2 roof carrier protector.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. Install the No. 2 roof carrier protector as shown in the illustration.

        A01CQ0PC01
        *1 No. 2 Roof Carrier Protector - -

  2. INSTALL NO. 1 ROOF CARRIER PROTECTOR


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the No. 1 roof carrier protector.


      1. Remove the peeling paper from the face of the No. 1 roof carrier protector.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. Install the No. 1 roof carrier protector as shown in the illustration.

        A01CQUEC01
        *1 No. 1 Roof Carrier Protector - -

  3. INSTALL NO. 1 ROOF CARRIER SEAL


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the No. 1 roof carrier seal.


      1. Remove the peeling paper from the face of the No. 1 roof carrier seal.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. Install the No. 1 roof carrier seal as shown in the illustration.

        A01CMQR

  4. INSTALL FRONT ROOF RACK RETAINER LH


    1. Attach the claw to install the front roof rack retainer LH.

  5. INSTALL REAR ROOF RACK LEG LH


    1. When reusing the screw:


      1. Clean the threaded portion on the vehicle body with non-residue solvent.

      2. Apply adhesive to the threads of the 2 screws.

        Adhesive
        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    2. Using a T30 "TORX" socket wrench, install the rear roof rack LH with the 2 screws.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  6. INSTALL CENTER ROOF RACK SUPPORT LH


    1. When reusing the screw:


      1. Clean the threaded portion on the vehicle body with non-residue solvent.

      2. Apply adhesive to the threads of the 2 screws.

        Adhesive
        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    2. Using a T30 "TORX" socket wrench, install the center roof rack support LH with the 2 screws.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  7. INSTALL FRONT ROOF RACK LEG LH


    1. When reusing the screw:


      1. Clean the threaded portion on the vehicle body with non-residue solvent.

      2. Apply adhesive to the threads of the 2 screws.

        Adhesive
        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    2. Using a T30 "TORX" socket wrench, install the front roof rack leg LH with the 2 screws.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  8. INSTALL ROOF CARRIER SEAL


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the roof carrier seal.


      1. Remove the peeling paper from the face of the roof carrier seal.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. A01CQ1D

        Install the roof carrier seal as shown in the illustration.

        Tech Tips

        Do not overlap the guide.

  9. INSTALL NO. 3 ROOF CARRIER SEAL LH


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the No. 3 roof carrier seal.


      1. Remove the peeling paper from the face of the No. 3 roof carrier seal.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. A01CRBF

        Install the No. 3 roof carrier seal as shown in the illustration.

        Tech Tips

        Do not overlap the guide.

  10. INSTALL NO. 2 ROOF CARRIER SEAL


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the No. 2 roof carrier seal.


      1. Remove the peeling paper from the face of the No. 2 roof carrier seal.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. A01CN23

        Install the No. 2 roof carrier seal as shown in the illustration.

        Tech Tips

        Do not overlap the guide.

  11. INSTALL REAR ROOF RACK LEG CUSHION LH


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the rear roof rack leg cushion LH.


      1. Remove the peeling paper from the face of the rear roof rack leg cushion LH.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. A01CNVCC02
        *1 Double-sided Tape
        *a Roof Carrier Protector End Line
        *b Rear Roof Rack Leg Cushion End Line
        *c 0 to 2.0 mm (0 to 0.0787 in.)

        Install the rear roof rack leg cushion LH as shown in the illustration.

        Tech Tips

        Do not allow the cushion to protrude from the roof rack.

  12. INSTALL FRONT ROOF RACK LEG CUSHION LH


    1. Clean the roof rack surface.


      1. Remove the double-sided tape from the roof rack.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Install the front roof rack leg cushion LH.


      1. Remove the peeling paper from the face of the front roof rack leg cushion LH.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. A01CRO7C02
        *1 Double-sided Tape
        *a Rear Roof Rack Leg Cushion End Line
        *b Roof Carrier Protector End Line
        *c 0 to 2.0 mm (0 to 0.0787 in.)

        Install the front roof rack leg cushion LH as shown in the illustration.

        Tech Tips

        Do not allow the cushion to protrude from the roof rack.