FRONT BUMPER(except Sport Package) DISASSEMBLY

PROCEDURE


  1. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

    Click here

  2. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

    Tech Tips

    Use the same procedure described for the LH side.

  3. REMOVE HEADLIGHT CLEANER WASHER NOZZLE COVER LH (w/ Headlight Cleaner System)

    Click here

  4. REMOVE HEADLIGHT CLEANER WASHER NOZZLE COVER RH (w/ Headlight Cleaner System)

    Tech Tips

    Use the same procedure described for the LH side.

  5. REMOVE NO. 2 HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

    Click here

  6. REMOVE NO. 3 ENGINE ROOM WIRE


    1. w/ LEXUS Parking Assist-sensor System:

      Disconnect the 4 connectors.

    2. w/ Panoramic View Monitor System:

      Disconnect the connector.

    3. w/ Dynamic Radar Cruise Control System:

      Disconnect the connector.

    4. w/o LEXUS Parking Assist-sensor System:

      Detach the 7 clamps and remove the No. 3 engine room wire.

    5. Detach the 16 clamps and remove the No. 3 engine room wire.

      B002KXMC02
      *A w/ LEXUS Parking Assist-sensor System *B w/ Panoramic View Monitor System
      *C w/ Dynamic Radar Cruise Control System *D w/o LEXUS Parking Assist-sensor System

  7. REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  8. REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  9. REMOVE CLEARANCE LIGHT ASSEMBLY LH


    1. for LED Type Turn Signal Light:

      Click here

    2. for Bulb Type Turn Signal Light:

      Click here

  10. REMOVE CLEARANCE LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)

    Click here

  12. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE FRONT BUMPER GUARD COVER LH (w/o Fog Light)


    1. B002I47

      Remove the 3 screws and front bumper guard cover LH.

  14. REMOVE FRONT BUMPER GUARD COVER RH (w/o Fog Light)

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE FRONT BUMPER NO. 2 RETAINER BRACKET


    1. B002JBK

      Remove the 3 screws.

    2. Detach the 2 claws and remove the front bumper No. 2 retainer bracket.

  16. REMOVE FRONT BUMPER NO. 1 RETAINER BRACKET

    Tech Tips

    Use the same procedure described for the front bumper No. 2 retainer bracket.

  17. REMOVE AIR INTAKE DUCT LH


    1. B002I9K

      Remove the 2 clips.

    2. Detach the 2 guides and remove the air intake duct LH.

  18. REMOVE AIR INTAKE DUCT RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE NO. 2 RADIATOR GRILLE GARNISH


    1. B002ILR

      Remove the screw.

    2. Detach the 4 claws and remove the No. 2 radiator grille garnish.

  20. REMOVE RADIATOR GRILLE GARNISH

    Tech Tips

    Use the same procedure described for the No. 2 radiator grille garnish.

  21. REMOVE HOOD TO FRONT END PANEL SEAL


    1. B002JOY

      Detach the 13 clips and remove the hood to front end panel seal.

  22. REMOVE RADIATOR GRILLE ASSEMBLY

    Click here

  23. REMOVE FRONT BUMPER NO. 2 GUARD PAD LH


    1. B002JW1

      Remove the 3 clips and front bumper No. 2 guard pad LH.

  24. REMOVE FRONT BUMPER NO. 2 GUARD PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. REMOVE NO. 2 MOULDING TAPE

    Tech Tips


    • When removing the No. 2 moulding tape, heat the front bumper cover and No. 2 moulding tape using a heat light.

    • Use the same procedure described for the other side.

    Standard
    Item Temperature
    Front Bumper Cover 20 to 30°C (68 to 86°F)
    No. 2 Moulding Tape 20 to 30°C (68 to 86°F)

    Note

    Do not heat the front bumper cover and No. 2 moulding tape excessively.


    1. B002HOK

      Remove the No. 2 moulding tape.