REAR BUMPER DISASSEMBLY

PROCEDURE


  1. REMOVE KICK DOOR CONTROL BRACKET (w/ Hands Free Power Back Door)

    Click here

  2. REMOVE KICK DOOR CONTROL SENSOR (w/ Hands Free Power Back Door)

    Click here

  3. REMOVE REAR FOG LIGHT SET (w/ Rear Fog Light)

    Click here

  4. REMOVE FOG LIGHT COVER LH (w/ Rear Fog Light)

    Click here

  5. REMOVE NO. 2 LUGGAGE ROOM WIRE


    1. w/o Rear Fog Light:


      1. w/ LEXUS Parking Assist-sensor System:

        Disconnect the 4 connectors.

        Note

        Do not apply excessive loads to the retainer. Otherwise, it may peel off.

        Tech Tips

        Disconnect the connector while pressing the ultrasonic sensor with your hand.

      2. w/o Hands Free Power Back Door:

        Detach the 6 clamps and remove the No. 2 luggage room wire.

      3. w/ Hands Free Power Back Door:

        Detach the 10 clamps and remove the No. 2 luggage room wire.

        B002HNAC04
        *A w/ Hands Free Power Back Door - -

    2. w/ Rear Fog Light:


      1. w/o LEXUS Parking Assist-sensor System, Hands Free Power Back Door:

        Detach the 5 clamps and remove the No. 2 luggage room wire.

      2. w/ LEXUS Parking Assist-sensor System:

        Disconnect the 4 connectors.

        Note

        Do not apply excessive loads to the retainer. Otherwise, it may peel off.

        Tech Tips

        Disconnect the connector while pressing the ultrasonic sensor with your hand.

      3. w/o Hands Free Power Back Door:

        Detach the 10 clamps and remove the No. 2 luggage room wire.

      4. w/ Hands Free Power Back Door:

        Detach the 14 clamps and remove the No. 2 luggage room wire.

        B002KZCC02
        *A w/ Hands Free Power Back Door *B w/ Rear Fog Light

  6. REMOVE REAR CORNER ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  7. REMOVE REAR CENTER ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  8. REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here

  9. REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here

  10. REMOVE REAR BUMPER LOWER COVER


    1. Remove the 4 screws.

    2. Remove the 2 clips.

    3. Remove the 8 outside moulding retainers.

    4. Detach the 4 claws and remove the rear bumper lower cover.

      B002KLA

  11. REMOVE REFLEX REFLECTOR ASSEMBLY LH


    1. B002HDT

      Remove the screw.

    2. Detach the guide and remove the reflex reflector assembly LH.

  12. REMOVE REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE REAR BUMPER CORNER EXTENSION RH


    1. B002HK2

      Remove the 2 screws and the rear bumper corner extension RH.

  14. REMOVE REAR BUMPER LOWER SIDE RETAINER LH


    1. B002JSL

      Remove the 2 screws.

    2. Detach the 4 claws, guide and remove the rear bumper lower side retainer LH.

  15. REMOVE REAR BUMPER LOWER SIDE RETAINER RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE REAR BUMPER LOWER RETAINER LH


    1. B002H6J

      Remove the 3 screws.

    2. Detach the 2 guides and remove the rear bumper lower retainer LH.

  17. REMOVE REAR BUMPER LOWER RETAINER RH


    1. B002KBP

      Remove the 2 screws.

    2. Detach the 2 guides and remove the rear bumper lower retainer RH.

  18. REMOVE NO. 1 MOULDING TAPE

    Tech Tips


    • When removing the No. 1 moulding tape, heat the rear bumper cover and No. 1 moulding tape using a heat light.

    • Use the same procedure described for the other side.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)
    No. 1 Moulding Tape 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover and No. 1 moulding tape excessively.


    1. B002J0E

      Remove the No. 1 moulding tape.

  19. REMOVE REAR BUMPER PAD

    Tech Tips


    • When removing the rear bumper pad, heat the rear bumper cover and rear bumper pad using a heat light.

    • Use the same procedure described for the other side.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)
    Rear Bumper Pad 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover and rear bumper pad excessively.


    1. B002HZ7

      Remove the rear bumper pad.