REAR BUMPER REASSEMBLY

PROCEDURE


  1. INSTALL REAR BUMPER PAD

    Tech Tips


    • When installing the rear bumper pad, heat the rear bumper cover and rear bumper pad using a heat light.

    • Use the same procedure described for the other side.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)
    Rear Bumper Pad 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover and rear bumper pad excessively.


    1. Clean the rear bumper cover surface.


      1. Using a heat light, heat the rear bumper cover surface.

      2. Remove the double-sided tape from the rear bumper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    2. B002HZ7C04
      *a Scribed Line

      Install a new rear bumper pad.


      1. Using a heat light, heat the rear bumper cover and rear bumper pad.

      2. Remove the peeling paper from the face of the rear bumper pad.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Align the rear bumper pad with the scribed line on the rear bumper cover and install it as shown in the illustration.

        Tech Tips

        Press the rear bumper pad firmly to install it.

  2. INSTALL NO. 1 MOULDING TAPE

    Tech Tips


    • When installing the No. 1 moulding tape, heat the rear bumper cover and No. 1 moulding tape using a heat light.

    • Use the same procedure described for the other side.

    Note

    Do not heat the rear bumper cover and No. 1 moulding tape excessively.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)
    No. 1 Moulding Tape 20 to 30°C (68 to 86°F)

    1. Clean the rear bumper cover surface.


      1. Using a heat light, heat the rear bumper cover surface.

      2. Remove the double-sided tape from the rear bumper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    2. B002JSTC03
      *a Scribed Line

      Install a new No. 1 moulding tape.


      1. Using a heat light, heat the rear bumper cover and No. 1 moulding tape.

      2. Remove the peeling paper from the face of the No. 1 moulding tape.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Align the No. 1 moulding tape with the scribed line on the rear bumper cover and install it as shown in the illustration.

        Tech Tips

        Press the No. 1 moulding tape firmly to install it.

  3. INSTALL REAR BUMPER LOWER RETAINER LH


    1. B002H6J

      Attach the 2 guides to install the rear bumper lower retainer LH.

    2. Install the 3 screws.

  4. INSTALL REAR BUMPER LOWER RETAINER RH


    1. B002KBP

      Attach the 2 guides to install the rear bumper lower retainer RH.

    2. Install the 2 screws.

  5. INSTALL REAR BUMPER LOWER SIDE RETAINER LH


    1. B002JSL

      Attach the guide, 4 claws and install the rear bumper lower side retainer LH.

    2. Install the 2 screws.

  6. INSTALL REAR BUMPER LOWER SIDE RETAINER RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL REAR BUMPER CORNER EXTENSION RH


    1. B002HK2

      Install the rear bumper corner extension RH with the 2 screws.

  8. INSTALL REFLEX REFLECTOR ASSEMBLY LH


    1. B002HDT

      Attach the guide to install the reflex reflector assembly LH.

    2. Install the screw.

  9. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  10. INSTALL REAR BUMPER LOWER COVER


    1. Attach the 4 claws to install the rear bumper lower cover.

    2. Install the 8 outside moulding retainers in the figure direction.

    3. Install the 2 clips.

    4. Install the 4 screws.

      B002KLA

  11. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here

  12. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here

  13. INSTALL REAR CORNER ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  14. INSTALL REAR CENTER ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  15. INSTALL NO. 2 LUGGAGE ROOM WIRE


    1. w/o Rear Fog Light:


      1. w/ LEXUS Parking Assist-sensor System:

        Connect the 4 connectors.

        Note

        Do not apply excessive loads to the retainer. Otherwise, it may peel off.

        Tech Tips

        Connect the connector while pressing the ultrasonic sensor with your hand.

      2. w/o Hands Free Power Back Door:

        Attach the 6 clamps to install the No. 2 luggage room wire.

      3. w/ Hands Free Power Back Door:

        Attach the 10 clamps to install the No. 2 luggage room wire.

        B002HNAC04
        *A w/ Hands Free Power Back Door - -

    2. w/ Rear Fog Light:


      1. w/o LEXUS Parking Assist-sensor System, Hands Free Power Back Door:

        Attach the 5 clamps to install the No. 2 luggage room wire.

      2. w/ LEXUS Parking Assist-sensor System:

        Connect the 4 connectors.

        Note

        Do not apply excessive loads to the retainer. Otherwise, it may peel off.

        Tech Tips

        Connect the connector while pressing the ultrasonic sensor with your hand.

      3. w/o Hands Free Power Back Door:

        Attach the 10 clamps to install the No. 2 luggage room wire.

      4. w/ Hands Free Power Back Door:

        Attach the 14 clamps to install the No. 2 luggage room wire.

        B002KZCC02
        *A w/ Hands Free Power Back Door *B w/ Rear Fog Light

  16. INSTALL FOG LIGHT COVER LH (w/ Rear Fog Light)

    Click here

  17. INSTALL REAR FOG LIGHT SET (w/ Rear Fog Light)

    Click here

  18. INSTALL KICK DOOR CONTROL SENSOR (w/ Hands Free Power Back Door)

    Click here

  19. INSTALL KICK DOOR CONTROL BRACKET (w/ Hands Free Power Back Door)

    Click here