CLEARANCE LIGHT ASSEMBLY(for LED Type Turn Signal Light) REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL CLEARANCE LIGHT LED UNIT ASSEMBLY LH

    Note


    • Perform work using rubber gloves.

    • Do not touch the clearance light LED unit assembly LH with bare hands.

    • If dirty, lightly wipe with a soft cloth.


    1. Install the clearance light LED unit assembly LH with the 5 screws.

    2. Connect the connector.

  2. INSTALL CLEARANCE LIGHT GASKET

    Note


    • Perform work using rubber gloves.

    • Do not touch the clearance light LED unit assembly LH with bare hands.

    • If dirty, lightly wipe with a soft cloth.


    1. B002K86C01
      B002JLO Area to Clean

      Clean the clearance light gasket installation groove.

    2. B002INQ

      Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.

      Tech Tips

      Use the peeling paper that is supplied with the clearance light gasket.

    3. Using scissors, cut the end of the clearance light gasket at a diagonal (45°).

    4. B002KXIC01
      B002H91 Starting Point

      Starting at the center front bumper assembly screw installation point, set the clearance light gasket into the straight groove counterclockwise until it meets the corner groove.

      Note

      Lightly set the gasket in place without pulling.

    5. Using 2 screwdrivers with their tips wrapped with peeling paper, push the clearance light gasket into the bottom of the groove.

    6. B002KEGC01
      B002I10 Corner Groove

      Set the clearance light gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.

      Note


      • Lightly set the gasket in place without pulling.

      • If the clearance light gasket is set while pulled, the gasket will be pushed up at the corner groove.

    7. B002H9FC01
      B002HVY Push In
      B002JLO Peeling Paper

      Repeat the following order while working in a circle back to the starting point: 1) Set clearance light gasket into straight groove, 2) push into bottom of groove, 3) set into the corner groove and 4) push into bottom of groove.

    8. B002IE7C01
      *a 10 mm (0.3937 in.)
      B002I10 Corner Groove

      Using scissors, cut the clearance light gasket at a 45° angle at the starting point so that the gasket overlaps itself 10 mm (0.3937 in.) or more and set the gasket in place.

    9. Check the installation condition of the clearance light gasket.

      OK
      Gasket not pushed up or protruding.
      No gap where gasket overlaps.

      Note

      Check the corners carefully since the gasket can easily become pushed up in those areas.

  3. INSTALL PARKING AND CLEARANCE LIGHT LENS LH

    Note


    • Perform work using rubber gloves.

    • Do not touch the parking and clearance light lens LH with bare hands.

    • If dirty, lightly wipe with a soft cloth.


    1. Clean the clearance light gasket contact surface.

    2. Set the parking and clearance light lens LH in place.

    3. B002HDKC01
      *a Base Point

      Attach the 5 claws.

      Tech Tips

      Attach the claw at the base point first.

    4. Using a T20H "TORX" screwdriver, install the 2 screws.

    5. Install the 4 screws.

    6. Check the condition of the clearance light gasket.

      OK
      Gasket contacts parking and clearance light lens LH and does not protrude out.