HEADLIGHT ASSEMBLY(for LED Headlight) REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL HEADLIGHT FAN LH


    1. Install the headlight fan LH with the 2 screws.

    2. Connect the connector.

  2. INSTALL HEADLIGHT UNIT ASSEMBLY LH

    Note


    • Perform work using rubber gloves.

    • Do not touch the headlight unit assembly LH and other components removed during this procedure with bare hands.

    • If dirty, lightly wipe with a soft cloth.


    1. B002H1RC01
      *1 Rail

      Align the headlight unit assembly LH with the rail and set the headlight unit assembly LH onto the horizontal aiming screw.

    2. B002I88

      While holding the headlight unit assembly LH with one hand so that it does not fall over, tighten the horizontal aiming screw 20 rotations until the headlight unit assembly LH is connected.

    3. B002IA1

      Attach the pivot collar.

    4. Install the center lens cover:


      1. Attach the guide to install the center lens cover.

      2. Install the screw.

    5. Install the inner lens cover:


      1. Attach the guide to install the inner lens cover.

      2. Install the screw.

    6. Tighten the horizontal aiming screw until the protrusion amount is the same as that recorded.

  3. INSTALL HEADLIGHT LENS GASKET


    1. B002KAWC01
      B002JLO Area to Clean

      Clean the headlight lens gasket installation groove.

    2. B002INQ

      Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.

      Tech Tips

      Use the peeling paper that is supplied with the headlight lens gasket.

    3. Using scissors, cut the end of the headlight lens gasket at a diagonal (45°).

    4. B002HY7C01
      B002H91 Starting Point

      Starting at the center headlight lens LH screw installation point, set the headlight lens gasket into the straight groove counterclockwise until it meets the corner groove.

      Note

      Lightly set the gasket in place without pulling.

    5. Using 2 screwdrivers with their tips wrapped with peeling paper, push the headlight lens gasket into the bottom of the groove.

    6. B002KFHC01
      B002I10 Corner Groove

      Set the headlight lens gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.

      Note


      • Lightly set the gasket in place without pulling.

      • If the headlight lens gasket is set while pulled, the gasket will be pushed up at the corner groove.

    7. B002KTDC01
      B002HVY Push In
      B002JLO Peeling Paper

      Repeat the following order while working in a circle back to the starting point: 1) Set headlight lens gasket into straight groove, 2) push into bottom of groove, 3) set into the corner groove and 4) push into bottom of groove.

    8. B002J0JC01
      *a 10 mm (0.3937 in.)
      B002I10 Corner Groove

      Using scissors, cut the headlight lens gasket at a 45° angle at the starting point so that the gasket overlaps itself 10 mm (0.3937 in.) or more and set the gasket in place.

    9. Check the installation condition of the headlight lens gasket.

      OK
      Gasket not pushed up or protruding.
      No gap where gasket overlaps.

      Note

      Check the corners carefully since the gasket can easily become pushed up in those areas.

  4. INSTALL HEADLIGHT LENS LH

    Note


    • Perform work using rubber gloves.

    • Do not touch the headlight lens LH with bare hands.

    • If dirty, lightly wipe with a soft cloth.


    1. Clean the headlight lens gasket contact surface.

    2. Set the headlight lens LH in place.

    3. Attach the 8 claws.

      Tech Tips

      Attach the claw at the base point first.

      B002JIJC01
      *a Base Point - -

    4. Using a T20H "TORX" screwdriver, install the 3 screws.

    5. Install the 3 screws.

    6. Check the condition of the headlight lens gasket.

      OK
      Gasket contacts headlight lens LH and does not protrude out.

  5. INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING


    1. Install a new headlight leveling motor base packing.

  6. INSTALL HEADLIGHT LEVELING MOTOR LH


    1. Set the tip of the aiming screw of the headlight leveling motor LH onto the headlight unit assembly LH.

    2. Tighten the aiming screw of the headlight leveling motor LH the same number of rotations recorded when removing it to connect the headlight leveling motor LH.

    3. B002HL9C01
      *1 Aiming Screw
      B002HVY Counterclockwise

      Insert the headlight leveling motor LH.

    4. Turn the headlight leveling motor LH counterclockwise to install it.

      Tech Tips

      For the headlight assembly RH, turn the headlight leveling motor RH clockwise to install it.

    5. Tighten the aiming screw 20 rotations.

    6. Connect the connector.

  7. INSTALL HEADLIGHT GASKET

    Click here

  8. INSTALL HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY LH

    Click here