LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    DATA LIST


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body, AFS*1 or HL AutoLeveling*2 / Data List / All Data.


      • *1: for Triple Beam Headlight

      • *2: for Single Beam Headlight

    5. According to the display on the GTS, read the Data List.


      Body Electrical > AFS > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Clearance Light State Clearance light state OFF or ON

      OFF: Clearance lights off

      ON: Clearance lights on

      -
      Right Cornering Light/Front Side Illuminate Light State Cornering light RH state OFF or ON

      OFF: Cornering light RH off

      ON: Cornering light RH on

      -
      Left Cornering Light/Front Side Illuminate Light State Cornering light LH state OFF or ON

      OFF: Cornering light LH off

      ON: Cornering light LH on

      -
      Daylight Operating State Daytime running light state OFF or ON

      OFF: Daytime running lights off

      ON: Daytime running lights on

      The display is different depending on the destination.
      +B Voltage Value Headlight ECU sub-assembly LH +B power supply voltage value 0 to 19.75 V 11 to 14 V -
      Traveling Direction Traveling direction Not Fwd or Fwd

      Not Fwd: Shift lever in R or N position

      Fwd: Shift lever not in R or N position

      -
      Steering Sensor Initialization Status Steering sensor initialization state Incomplete or Completed

      Incomplete: Steering sensor zero point calibration incomplete

      Completed: Steering sensor zero point calibration completed

      -
      Headlight Low Beam State Low beam headlight state OFF or ON

      OFF: Low beam headlights off

      ON: Low beam headlights on

      -
      Headlight High Beam State High beam headlight state OFF or ON

      OFF: High beam headlights off

      ON: High beam headlights on

      -
      DRL State Daytime running light state OFF or ON

      OFF: Daytime running lights off

      ON: Daytime running lights on

      The display is different depending on the destination.
      Engine Engine condition Run or Stop

      Run: Engine is running

      Stop: Engine is stopped

      -
      +B Headlight ECU sub-assembly LH IG power supply voltage value 0 to 19.75 V 11 to 14 V -
      Steering Sens Signal Steering sensor signal value -384.0 deg to 382.5 deg 0.0 deg 0.0 deg is displayed when steering wheel is centered.
      Steering Sens Center Pos Steering sensor center position -3072.0 deg to 3070.5 deg 0.0 deg 0.0 deg is displayed when steering wheel is centered.
      FR Wheel Speed Front right wheel speed 0.00 to 260.00 km/h (161.56 mph)

      Almost same as actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      -
      FL Wheel Speed Front left wheel speed 0.00 to 260.00 km/h (161.56 mph)

      Almost same as actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      -
      Vehicle Speed Vehicle speed 0.00 to 260.00 km/h (161.56 mph)

      Almost same as actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      -
      Rear Height Adjust Valid Flag Rear height adjustment range Valid or Invalid

      Valid: Rear height control sensor sub-assembly RH value within normal range

      Invalid: Rear height control sensor sub-assembly RH value out of normal range

      -
      Init Writing Count Number of times initialization performed 0 to 255 Number of times initialization performed -
      Sensor Initialization Hist Sensor initialization history not comp, 10%, 25%, 50%, 75%, 100% or completed

      not comp: Headlight ECU sub-assembly LH not initialized after replacing.

      10%: Initialization completed when fuel tank was 10% full

      25%: Initialization completed when fuel tank was 25% full

      50%: Initialization completed when fuel tank was 50% full

      75%: Initialization completed when fuel tank was 75% full

      100%: Initialization completed when fuel tank was 100% full

      completed: ECU not replaced and ECU has not been initialized at workshop.

      -
      Number Of Trouble Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Body Electrical > HL AutoLeveling > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Headlight Low Beam State Low beam headlight state OFF or ON

      OFF: Low beam headlights off

      ON: Low beam headlights on

      -
      Headlight High Beam State High beam headlight state OFF or ON

      OFF: High beam headlights off

      ON: High beam headlights on

      -
      DRL Operating State Daytime running light state OFF or ON

      OFF: Daytime running light off

      ON: Daytime running light on

      The display is different depending on the destination.
      Daylight Operating State Daytime running light state OFF or ON

      OFF: Daytime running light off

      ON: Daytime running light on

      The display is different depending on the destination.
      Clearance Light State Clearance light state OFF or ON

      OFF: Clearance light off

      ON: Clearance light on

      -
      Right Cornering Light State Cornering light RH state OFF or ON

      OFF: Cornering light RH off

      ON: Cornering light RH on

      w/ Front Fog Light
      Left Cornering Light State Cornering light LH state OFF or ON

      OFF: Cornering light LH off

      ON: Cornering light LH on

      w/ Front Fog Light
      Height Sens Pw Supply Val Height control sensor power supply value 0.00 to 5.00 V 4.61 to 5.00 V -
      Rr Height Sens Signal Val Rear height control sensor signal value 0.00 to 5.00 V 0.50 to 4.50 V The value changes according to the vehicle height.
      Front Right Wheel Speed Value Front right wheel speed 0.00 to 260.00 km/h (161.56 mph)

      Almost same as actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      -
      Front Left Wheel Speed Value Front left wheel speed 0.00 to 260.00 km/h (161.56 mph)

      Almost same as actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      -
      Vehicle Speed Vehicle speed 0.00 to 260.00 km/h (161.56 mph)

      Almost same as actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      -
      Rear Height Adjust Value Rear height adjustment offset value 0 to 1023 Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed) -
      Rear Height Adjust Valid Flag Rear height adjustment range Valid or Invalid

      Valid: Rear vehicle height calibration not completed

      Invalid: Rear vehicle height calibration completed

      -
      Init Writing Count Number of times initialization performed 0 to 255 Number of times initialization performed -
      Sensor Initialization Hist Sensor initialization history not comp, 10%,25%, 50%, 75%,100% or complied

      not comp: Headlight ECU sub-assembly LH not initialized after replacing.

      10%: Initialization completed when fuel tank was 10% full

      25%: Initialization completed when fuel tank was 25% full

      50%: Initialization completed when fuel tank was 50% full

      75%: Initialization completed when fuel tank was 75% full

      100%: Initialization completed when fuel tank was 100% full

      completed: ECU not replaced and ECU has not been initialized at workshop.

      -
      Steering Sensor Signal Steering angle sensor value -384 to 382.5 deg 0.0 deg 0.0 deg is displayed when steering wheel is centered.
      Steering Sensor Center Position Steering angle sensor center position -3072 to 3070.5 deg 0.0 deg 0.0 deg is displayed when steering wheel is centered.
      +B Voltage Value Headlight light control ECU power supply voltage value 0 to 19.75 V 11 to 14 V -
      Number Of Trouble Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      IG SW power switch on (IG) signal OFF or ON

      OFF: power switch off

      ON: power switch on (IG)

      "OFF" is also displayed for this item when the power switch is on (ACC).
      FR Door Courtesy SW Front door courtesy light switch RH OFF or ON

      OFF: Front door RH open

      ON: Front door RH closed

      -
      Dimmer SW Headlight dimmer switch high position signal OFF or ON

      OFF: Headlight dimmer switch in low position

      ON: Headlight dimmer switch in high or high flash position

      -
      Passing Light SW Headlight dimmer switch high flash position (pass) signal OFF or ON

      OFF: Headlight dimmer switch not in high flash position

      ON: Headlight dimmer switch in high flash position

      -
      Rear Fog Light SW Rear fog light switch signal OFF or ON

      ON: Rear fog light switch on

      OFF: Rear fog light switch off

      w/ Rear Fog Light
      Front Fog Light SW Front fog light switch signal OFF or ON

      OFF: Front fog light switch off

      ON: Front fog light switch on

      w/ Front Fog Light
      Auto Light SW Headlight dimmer switch (light control switch) AUTO position signal OFF or ON

      OFF: Headlight dimmer switch (light control switch) not in AUTO position

      ON: Headlight dimmer switch (light control switch) in AUTO position

      -
      Head Light SW (Head) Headlight dimmer switch (light control switch) head position signal OFF or ON

      OFF: Headlight dimmer switch (light control switch) not in head position

      ON: Headlight dimmer switch (light control switch) in head position

      -
      Head Light SW (Tail) Headlight dimmer switch (light control switch) tail position signal OFF or ON

      OFF: Headlight dimmer switch (light control switch) in neither tail nor head position

      ON: Headlight dimmer switch (light control switch) in tail or head position

      -
      Light Sensor Illuminance Light control sensor illuminance 0 to 17600 lx Value is output according to ambient light level -
      Light Sensor Connection Status Light control sensor connection status OFF or ON

      ON: Light control sensor is connected

      OFF: Light control sensor is not connected

      -
      Response Time Changes the delay timing of lighting the taillights when going into a tunnel when the headlight dimmer switch (light control switch) is in the AUTO position. Normal, Long Customized setting displayed Customized setting displayed
      Sensitivity Sensitivity setting of automatic light control system Normal, Dark2, Dark1, Light1 or Light2 Customized setting displayed -
      DRL Function ON/OFF of the DRL function Normal, Dark2, Dark1, Light1 or Light2 Customized setting displayed Vehicles displaying the Item "DRL Function" on the GTS
      Disp Ex ON Sen Sets the display light (meter, audio, etc.) dim starting level Normal, Dark2, Dark1, Light or Light2 Customized setting displayed -
      Disp Ex OFF Sen Sets the display light (meter, audio, etc.) dim return level NORMAL, DARK2, DARK1, LIGHT1, LIGHT2 Customized setting displayed -
      Light Auto OFF Delay Keep the headlights on for a certain period of time after turning the power switch off and closing all doors with the low beam headlights on. OFF or ON Customized setting displayed Vehicles displaying the Item "Light Auto OFF Delay" on the GTS
      Follow Me Home Lighting Time Customized length of time that low beam headlights are illuminated when power switch is off and headlight dimmer switch is pulled to flash headlights once 30 s, 60 s, 90 s, or 120 s Customized setting displayed w/ Follow Me Home System
      Light up Clearance Lights at Door Unlock Function Turns on the clearance lights, taillights and the license plate lights for 15 seconds when the doors are unlocked by the smart key or the wireless key. OFF or ON Customized setting displayed -
      The Number of DTC Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Body Electrical > Combination Meter > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Turn Signal Switch (Right) Turn signal switch (right) signal OFF or ON

      OFF: Turn signal switch (right) off

      ON: Turn signal switch (right) on

      -
      Turn Signal Switch (Left) Turn signal switch (left) signal OFF or ON

      OFF: Turn signal switch (left) off

      ON: Turn signal switch (left) on

      -
      Hazard Flasher Switch Hazard switch signal OFF or ON

      OFF: Hazard switch off

      ON: Hazard switch on

      -
  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body, AFS*1 or HL AutoLeveling*2 / Active Test.


      • *1: for Triple Beam Headlight

      • *2: for Single Beam Headlight

    5. According to the display on the GTS, perform the Active Test.


      Body Electrical > AFS > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Drive The Leveling Motor Operates the headlight leveling motor Up, Down or Stop Perform with the vehicle stopped, power switch on (READY) and low beam headlights illuminated.
      Clearance Light Illuminates clearance lights OFF or ON -
      Headlight Low Beam Illuminates the low beam headlights OFF or ON -
      Headlight High Beam Illuminates the high beam headlights OFF or ON -
      Daytime Running Light Illuminates daytime running lights OFF or ON -
      Cornering Light Illuminates cornering lights OFF or ON -

      Body Electrical > HL AutoLeveling > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Drive The Leveling Motor Operates the headlight leveling motor Up, Down or Stop Perform with the vehicle stopped, power switch on (READY) and low beam headlights illuminated.
      Clearance Light Illuminates clearance lights OFF or ON -
      Headlight Low Beam Illuminates the low beam headlights OFF or ON -
      Headlight High Beam Illuminates the high beam headlights OFF or ON -
      Daytime Running Light Illuminates daytime running lights OFF or ON -
      Cornering Light Illuminates cornering lights OFF or ON -

      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Daytime Running Light Daytime running light OFF or ON -
      Taillight Relay Taillight relay OFF or ON -
      Headlight Relay Low beam headlight relay OFF or ON -
      Head Light Hi Headlight dimmer relay OFF or ON -
      Front Fog Light Relay Front fog light relay OFF or ON The Headlight dimmer switch (fog switch) is in the tail position. (w/ Front Fog Light)
      Rear Fog Light Relay Rear fog light relay OFF or ON The Headlight dimmer switch (fog switch) is in the tail position. (w/ Rear Fog Light)