OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Apply auxiliary battery voltage and check the operation of the mirror.

         OK

         Measurement Condition Specified Condition Auxiliary battery positive (+) → Terminal 1 (MV) Auxiliary battery negative (-) → Terminal 10 (M+) Turns upward Auxiliary battery positive (+) → Terminal 10 (M+) Auxiliary battery negative (-) → Terminal 1 (MV) Turns downward Auxiliary battery positive (+) → Terminal 9 (MH) Auxiliary battery negative (-) → Terminal 10 (M+) Turns right Auxiliary battery positive (+) → Terminal 10 (M+) Auxiliary battery negative (-) → Terminal 9 (MH) Turns left

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   2. Check the operation of the retractable mirror.

      Note

      
      

      • Disconnect and reconnect the auxiliary battery between each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      
      
      1. 

         *a	(A) Forward position
         *b	(B)
         *c	(C) Driving position
         *d	(D)
         *e	(E) Retracted position
         *f	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

         OK

         Tester Connection Condition Specified Condition Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to (A) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to (C) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to (C)

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   3. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the side turn signal light assembly LH.

      
      

      1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

         OK
         Measurement Connection Specified Condition Auxiliary battery positive (+) → Terminal 16 (TRN+) Auxiliary battery negative (-) → Terminal 12 (TRN-) Side turn light illuminates

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   4. Check the operation of the mirror heater. (w/ Mirror Heater)

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition Terminal 4 (HTR+) - Terminal 12 (TRN-) 25°C (75°F) 6.8 to 10.2 Ω

         If the result is not as specified, replace the outer rear view mirror assembly LH.

      3. Connect the cable from the positive (+) auxiliary battery terminal to terminal 4 and the negative (-) auxiliary battery terminal to terminal 12, and then check that the mirror becomes warm.

         Tech Tips

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   5. Check the EC mirror operation. (w/ EC Mirror)

      
      

      1. Connect a new 1.5 V dry-cell battery.

      2. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)
         *b	Bright
         *c	Dark

         Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

         OK
         Measurement Connection Specified Condition Positive (+) end of the 1.5 V dry-cell battery → Terminal 7 (EC+) Negative (-) end of the 1.5 V dry-cell battery → Terminal 15 (EC-) Mirror surface becomes dark

         Note

         Do not apply a voltage of 1.5 V or higher.

         If the result is not as specified, replace the outer rear view mirror assembly LH.

2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Apply auxiliary battery voltage and check the operation of the mirror.

         OK

         Measurement Condition Specified Condition Auxiliary battery positive (+) → Terminal 1 (MV) Auxiliary battery negative (-) → Terminal 10 (M+) Turns upward Auxiliary battery positive (+) → Terminal 10 (M+) Auxiliary battery negative (-) → Terminal 1 (MV) Turns downward Auxiliary battery positive (+) → Terminal 9 (MH) Auxiliary battery negative (-) → Terminal 10 (M+) Turns left Auxiliary battery positive (+) → Terminal 10 (M+) Auxiliary battery negative (-) → Terminal 9 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   2. Check the operation of the retractable mirror.

      Note

      
      

      • Disconnect and reconnect the auxiliary battery between each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      
      
      1. 

         *a	(A) Forward position
         *b	(B)
         *c	(C) Driving position
         *d	(D)
         *e	(E) Retracted position
         *f	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

         OK

         Tester Connection Condition Specified Condition Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to (A) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to (E) Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to (C) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Auxiliary battery positive (+) → Terminal 11 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to (C)

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   3. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the side turn signal light assembly RH.

      
      

      1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

         OK
         Measurement Connection Specified Condition Auxiliary battery positive (+) → Terminal 16 (TRN+) Auxiliary battery negative (-) → Terminal 12 (TRN-) Side turn light illuminates

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   4. Check the operation of the mirror heater. (w/ Mirror Heater)

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition Terminal 4 (HTR+) - Terminal 12 (TRN-) 25°C (75°F) 6.8 to 10.2 Ω

         If the result is not as specified, replace the outer rear view mirror assembly RH.

      3. Connect the cable from the positive (+) auxiliary battery terminal to terminal 4 and the negative (-) auxiliary battery terminal to terminal 12, and then check that the mirror becomes warm.

         Tech Tips

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   5. Check the EC mirror operation. (w/ EC Mirror)

      
      

      1. Connect a new 1.5 V dry-cell battery.

      2. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)
         *b	Bright
         *c	Dark

         Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

         OK
         Measurement Connection Specified Condition Positive (+) end of the 1.5 V dry-cell battery → Terminal 7 (EC+) Negative (-) end of the 1.5 V dry-cell battery → Terminal 15 (EC-) Mirror surface becomes dark

         Note

         Do not apply a voltage of 1.5 V or higher.

         If the result is not as specified, replace the outer rear view mirror assembly RH.