POWER BACK DOOR SYSTEM OPERATION CHECK

CHECK BASIC OPERATION

• *1: w/ Power Back Door Hazard Warning Light

• *2: w/ Hands Free Power Back Door

1. Conditions necessary for the power back door to open:

   
   

   • The back door is unlocked (except wireless one motion function).

   • The vehicle speed is 3 km/h (2 mph) or less (only when the power switch is on [IG]).

   • The shift lever is in P, the brake pedal is depressed or the parking brake lever is pulled up (this can be determined only when the power switch is on [IG]).

2. Check the opening operation.

   
   

   1. With the back door fully closed, push the combination switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice*1 and the back door starts opening.

   2. With the back door fully closed, push the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice*1 and the back door starts opening.

   3. With the back door fully closed, push the back door opener switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice*1 and the back door starts opening.

3. Check the close operation.

   
   

   1. With the back door fully open, push the combination switch assembly and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice*1 and the back door starts closing.

   2. With the back door fully open, push the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice*1 and the back door starts closing.

   3. With the back door fully open, push the back door control switch and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice*1 and the back door starts closing.

4. Check the operation when another input is detected during the opening or closing operation.

   
   

   1. During a power back door opening or closing operation, push the combination switch assembly again, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops. After the closing operation stops, press the combination switch assembly and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.

   2. During a power back door opening or closing operation, push the transmitter switch (electrical key transmitter sub-assembly) again, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops. After the closing operation stops, press the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.

   3. During a power back door closing operation via the back door control switch, push the door control switch again, and check that the power back door warning buzzer sounds for 0.2 seconds and the power back door closing operation stops. After the closing operation stops, press the back door control switch and check that the power back door operates until it reaches the fully open position or the automatic opening operation stop position.

   4. During a power back door opening or closing operation, push the back door opener switch assembly, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door operation switches to manual operation mode.

   5. During a power back door opening or closing operation, push the door control switch, and check that the power back door warning buzzer sounds for 0.2 seconds and the back door stops.

   6. During a power back door opening or closing operation, kick operation and check that the power back door warning buzzer sounds for 0.2 seconds and the and the back door stops.*2

CHECK WIRELESS ONE MOTION FUNCTION

1. Check the wireless one motion operation.

   
   

   1. With all doors locked, push the transmitter switch (electrical key transmitter sub-assembly) and check that the power back door warning buzzer sounds for 0.8 seconds, the hazard warning lights flash twice* and the back door starts opening.

      
      

      • *: w/ Power Back Door Hazard Warning Light

CHECK JAM PROTECTION FUNCTION

1. Check the jam protection function (the power back door sensor assembly) while the power back door is closing.

   Note

   Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.

   
   

   1. Fully open the back door.

   2. Press a switch to close the power back door.

   3. While the back door is closing, press a power back door sensor assembly using the handle of a hammer or equivalent.

   4. Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door reverses a certain amount and stops.

2. Check the jam protection function (the pulse sensor in the power back door unit assembly set) while the power back door is closing.

   Note

   Do not check this function using a part of your body such as your hand. Also, pay thorough attention that nothing gets caught by accident in this process.

   
   

   1. Fully open the back door.

   2. Press a switch to close the power back door.

   3. While the back door is closing, insert a tire or equivalent between the door panel and vehicle body, in order to interrupt the closing operation.

   4. Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door reverses a certain amount and stops.

3. Check the jam protection function while the power back door is opening.

   Note

   Pay thorough attention that your body or your clothes, etc. do not get caught in the door by accident in this process.

   
   

   1. Fully close the back door.

   2. Press a switch to open the power back door.

   3. While the back door is opening, use your hands to press on the outside surface of the back door panel so that the operating speed decreases.

   4. Check that the buzzer sounds twice for 0.1 seconds, the jam protection function is immediately activated and the power back door stops.

CHECK ASSIST OPERATION

1. Check that the door automatically starts to fully close when the door is manually moved in the closing direction with the back door at rest.

CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When not using GTS)

1. Register open operation automatic stopped position in memory

   
   

   1. Open the back door by operating each switch.

   2. Operate each switch to stop the open operation when the back door reaches the desired automatic stopped position.

   3. When the back door control switch is pressed and held for 2 seconds or more with the back door at the stopped position, the buzzer sounds 4 times and the system memorizes the automatic stopped position for the open operation.

   4. Check that the back door stops at the memorized position when an open operation is performed with each switch.

2. Clear open operation automatic stopped position memory

   
   

   1. Open the back door by operating each switch.

   2. Stop the back door by operating each switch.

   3. When the back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.

CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When using GTS)

1. Register open operation automatic stopped position in memory

   
   

   1. Using the GTS, select the "Power Back Door Opening Adjust" customize setting.

      Click here

   2. According to the GTS display, set the customize setting.

   3. Check that the back door stops at the position set with the customize function when an open operation is performed with each switch.

2. Clear open operation automatic stopped position memory

   
   

   1. Open the back door by operating each switch.

   2. Stop the back door by operating each switch.

   3. When the back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.

CHECK AUTOMATIC OPENING OPERATION STOPPED POSITION MEMORIZATION FUNCTION (When using Multi-display)

1. Register open operation automatic stopped position in memory

   
   

   1. Using the multi-display, select the "Power back door opening adjust" customize setting.

      Click here

   2. According to the screen display, set the customize setting.

   3. Check that the back door stops at the position set with the customize function when an open operation is performed with each switch.

2. Clear open operation automatic stopped position memory

   
   

   1. Open the back door by operating each switch.

   2. Stop the back door by operating each switch.

   3. When the back door control switch is pressed and held for 7 seconds or more with the back door at the stopped position, the buzzer sounds 2 times and the system clears the automatic stopped position for the open operation.

CHECK POWER BACK DOOR CLOSE AND LOCK FUNCION

1. When the following conditions are met, check that all doors lock when pressing the door control switch after the power back door closes while carrying the transmitter switch (electrical key transmitter sub-assembly).

   
   

   • Back door is open

   • Door other than the back door is closed

   • Transmitter switch (electrical key transmitter sub-assembly) is not in the vehicle

   Tech Tips

   If the door control switch is operated with the hand holding the transmitter switch (electrical key transmitter sub-assembly), it may not operate due to being outside the key detection area.

CHECK HANDS FREE POWER BACK DOOR OPERATION (w/ Hands Free Power Back Door)