ROOF HEADLINING DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. REMOVE VANITY LIGHT ASSEMBLY

    Tech Tips

    Use the same procedure for both vanity light assemblies.


    1. A01H5XEC02
      *1 Bulb Holder
      *2 Claw A
      *3 Claw B

      Detach the 2 claws A and separate the bulb holder from the vanity light assembly as shown in the illustration.

    2. Detach the claw B and remove the vanity light assembly.

  2. REMOVE NO. 1 ROOF SILENCER PAD (for Normal Roof)


    1. A01H7GV

      Remove the No. 1 roof silencer pad.

  3. REMOVE NO. 2 ROOF SILENCER PAD (for Normal Roof)


    1. A01H7GB

      Remove the 2 No. 2 roof silencer pads.

  4. REMOVE NO. 3 ROOF SILENCER PAD (for Normal Roof)


    1. A01H85Z

      Remove the 2 No. 3 roof silencer pads.

  5. REMOVE REAR ROOF SILENCER PAD (for Normal Roof)


    1. A01H7YY

      Remove the rear roof silencer pad.

  6. REMOVE REAR ROOF SILENCER PAD (for Sliding Roof)


    1. A01H7TZ

      Remove the rear roof silencer pad.

  7. REMOVE NO. 4 ROOF SILENCER PAD (for Normal Roof)


    1. A01H6AH

      Remove the No. 4 roof silencer pad.

  8. REMOVE ROOF HEADLINING PAD (for Normal Roof)


    1. A01H76H

      Remove the 2 roof headlining pads.

  9. REMOVE ROOF HEADLINING PAD (for Sliding Roof)


    1. A01H7W0

      Remove the 2 roof headlining pads.

  10. REMOVE ROOF HEADLINING PAD (for Glass Roof)


    1. A01H6YP

      Remove the 2 roof headlining pads.

  11. REMOVE FRONT ROOF HEADLINING SIDE PAD (for Normal Roof)


    1. A01H73W

      Remove the 2 front roof headlining side pads.

  12. REMOVE ROOF HEADLINING END PAD (for Normal Roof)


    1. A01H6OP

      Remove the 2 roof headlining end pads.

  13. REMOVE ROOF HEADLINING END PAD (for Sliding Roof)


    1. A01H6W7

      Remove the 2 roof headlining end pads.

  14. REMOVE ROOF HEADLINING END PAD (for Glass Roof)


    1. A01H6ZE

      Remove the 2 roof headlining end pads.

  15. REMOVE NO. 1 ROOF WIRE (for Normal Roof)


    1. for LHD:


      1. A01H5W3

        Turn the visor connectors approximately 90° counterclockwise and remove them from the roof headlining.

      2. Remove each piece of tape and the No. 1 roof wire from the roof headlining.

        A01H5PEC01
        *A w/o Lane Departure Alert System *B w/ Lane Departure Alert System
        *1 No. 1 Roof Wire - -
        B002JLO Tape - -

      3. Remove the butyl tape remaining on the roof headlining.

    2. for RHD:


      1. A01H5W3

        Turn the visor connectors approximately 90° counterclockwise and remove them from the roof headlining.

      2. Remove each piece of tape and the No. 1 roof wire from the roof headlining.

        A01H74CC01
        *A w/o Lane Departure Alert System *B w/ Lane Departure Alert System
        *1 No. 1 Roof Wire - -
        B002JLO Tape - -

      3. Remove the butyl tape remaining on the roof headlining.

  16. REMOVE NO. 1 ROOF WIRE (for Sliding Roof)


    1. for LHD:


      1. A01H5W3

        Turn the visor connectors approximately 90° counterclockwise and remove them from the roof headlining.

      2. Remove each piece of tape and the No. 1 roof wire from the roof headlining.

        A01H8AWC01
        *A w/o Lane Departure Alert System *B w/ Lane Departure Alert System
        *1 No. 1 Roof Wire - -
        B002JLO Tape - -

      3. Remove the butyl tape remaining on the roof headlining.

    2. for RHD:


      1. A01H5W3

        Turn the visor connectors approximately 90° counterclockwise and remove them from the roof headlining.

      2. Remove each piece of tape and the No. 1 roof wire from the roof headlining.

        A01H88MC01
        *A w/o Lane Departure Alert System *B w/ Lane Departure Alert System
        *1 No. 1 Roof Wire - -
        B002JLO Tape - -

      3. Remove the butyl tape remaining on the roof headlining.

  17. REMOVE NO. 1 ROOF WIRE (for Glass Roof)


    1. for LHD:


      1. A01H5W3

        Turn the visor connectors approximately 90° counterclockwise and remove them from the roof headlining.

      2. Remove each piece of tape and the No. 1 roof wire from the roof headlining.

        A01H6QYC01
        *A w/o Lane Departure Alert System *B w/ Lane Departure Alert System
        *1 No. 1 Roof Wire - -
        B002JLO Tape - -

      3. Remove the butyl tape remaining on the roof headlining.

    2. for RHD:


      1. A01H5W3

        Turn the visor connectors approximately 90° counterclockwise and remove them from the roof headlining.

      2. Remove each piece of tape and the No. 1 roof wire from the roof headlining.

        A01H5URC01
        *A w/o Lane Departure Alert System *B w/ Lane Departure Alert System
        *1 No. 1 Roof Wire - -
        B002JLO Tape - -

      3. Remove the butyl tape remaining on the roof headlining.

  18. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here