ROOF HEADLINING REMOVAL

CAUTION / NOTICE / HINT

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

PROCEDURE

REMOVE DECK BOARD ASSEMBLY
1. Remove the deck board assembly.
REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY
1. Remove the No. 3 deck board sub-assembly.
REMOVE REAR DECK FLOOR BOX (w/ Spare Tire)
1. Remove the rear deck floor box.
REMOVE DECK FLOOR BOX LH (w/ Spare Tire)
1. Remove the 4 clips.
2. Detach the 4 guides and remove the deck floor box LH.
PRECAUTION

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work.

Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
1. w/o Spare tire:
  
  Detach the 2 claws and remove the battery service cover.
REMOVE REAR SEAT ASSEMBLY (for Manual Seat)

Click here
REMOVE REAR SEAT ASSEMBLY (for Power Seat)

Click here
REMOVE TONNEAU COVER ASSEMBLY
1. Remove the tonneau cover assembly.
REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY
1. Remove the No. 2 deck board sub-assembly.
REMOVE SPARE TIRE (w/ Spare Tire)
1. Remove the spare tire.
REMOVE DECK FLOOR BOX LH (w/o Spare Tire)
1. Remove the 4 clips.
2. Detach the 6 guides and remove the deck floor box LH.
REMOVE DECK FLOOR BOX RH (w/ Spare Tire)
1. Remove the 2 clips.
2. Detach the 4 guides and remove the deck floor box RH.
REMOVE DECK FLOOR BOX RH (w/o Spare Tire)
1. Remove the 2 clips.
2. Detach the 4 guides and remove the deck floor box RH.
REMOVE NO. 1 TOOL BOX SUB-ASSEMBLY (w/ Spare Tire)
1. Remove the screw.
2. Detach the 2 claws, clip and 5 guides and remove the No. 1 tool box sub-assembly.
REMOVE NO. 1 TOOL BOX SUB-ASSEMBLY (w/o Spare Tire)
1. Remove the screw.
2. Detach the 4 claws, 2 clips and 4 guides and remove the No. 1 tool box sub-assembly.
REMOVE NO. 2 TOOL BOX SUB-ASSEMBLY (w/ Spare Tire)
1. Remove the screw.
2. Detach the 2 clips and 4 guides and remove the No. 2 tool box sub-assembly.
REMOVE NO. 2 TOOL BOX SUB-ASSEMBLY (w/o Spare Tire)
1. Remove the screw.
2. Detach the clip and 4 guides and remove the No. 2 tool box sub-assembly.
REMOVE REAR FLOOR FINISH PLATE
1. Detach the 4 claws and 4 clips and remove the rear floor finish plate.
REMOVE DOOR SCUFF PLATE ASSEMBLY LH
1. *1 Protective Tape
  
  Put protective tape around the door scuff plate assembly LH.
2. *1 Claw A
  
  *2 Claw B
  
  Detach the 2 claws and guide on the front side of the door scuff plate assembly LH in the order shown in the illustration.
  Tech Tips
  
  Pull the door scuff plate assembly LH towards you in the direction indicated by the arrow in the illustration to detach claw A.
  
  Pull the door scuff plate assembly LH upwards in the direction indicated by the arrow in the illustration to detach claw B.
3. *1 Claw A
  
  *2 Claw B
  
  Detach the 2 claws and guide on the rear side of the door scuff plate assembly LH in the order shown in the illustration.
  Tech Tips
  
  Pull the door scuff plate assembly LH towards you in the direction indicated by the arrow in the illustration to detach claw A.
  
  Pull the door scuff plate assembly LH upwards in the direction indicated by the arrow in the illustration to detach claw B.
4. Pull the door scuff plate assembly LH upwards in the direction indicated by the arrow in the illustration to detach the 6 claws and remove the door scuff plate assembly LH.
REMOVE DOOR SCUFF PLATE ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE COWL SIDE TRIM BOARD LH
1. Remove the cap nut.
2. Detach the clip and remove the cowl side trim board LH.
REMOVE COWL SIDE TRIM BOARD RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Remove the front door opening trim weatherstrip LH.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR DOOR SCUFF PLATE LH
1. *1 Protective Tape
  
  Put protective tape around the rear door scuff plate LH.
2. *1 Claw A
  
  *2 Claw B
  
  Detach the 2 claws and guide on the front side of the rear door scuff plate LH in the order shown in the illustration.
  Tech Tips
  
  Pull the rear door scuff plate LH towards you in the direction indicated by the arrow in the illustration to detach claw A.
  
  Pull the rear door scuff plate LH upwards in the direction indicated by the arrow in the illustration to detach claw B.
3. *1 Claw A
  
  *2 Claw B
  
  Detach the 2 claws and guide on the rear side of the rear door scuff plate LH in the order shown in the illustration.
  Tech Tips
  
  Pull the rear door scuff plate LH towards you in the direction indicated by the arrow in the illustration to detach claw A.
  
  Pull the rear door scuff plate LH upwards in the direction indicated by the arrow in the illustration to detach claw B.
4. Pull the rear door scuff plate LH upwards in the direction indicated by the arrow in the illustration to detach the 4 claws and remove the rear door scuff plate LH.
REMOVE REAR DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
1. Remove the rear door opening trim weatherstrip LH.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

Tech Tips

Use the same procedure described for the LH side.

REMOVE FRONT PILLAR GARNISH ASSEMBLY LH

*1 Front Pillar Garnish Clip

*a Place hand here

Place your hand in the position shown in the illustration and pull the upper portion of the front pillar garnish assembly LH in the direction indicated by the arrow to detach the 2 front pillar garnish clips.

Tech Tips

Make the front pillar garnish assembly LH hang down from the front pillar garnish clip.
Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish assembly LH.

Tech Tips

Tape the tips of the needle-nose pliers before use.

Detach the 2 guides and remove the front pillar garnish assembly LH.

*1	Protective Tape	*2	Front Pillar Garnish Clip
*a	90°	-	-

Using your fingers, grasp the parts indicated by the arrows shown in the illustration and remove the front pillar garnish clip.

Note

If the front pillar garnish clip is damaged, replace it with a new one.
When the front pillar garnish clip cannot be removed by using your fingers:
1. While pressing the part indicated by the arrow shown in the illustration with your finger, lift the front pillar garnish clip in direction A.
2. While pulling in direction B, push the part indicated by the arrow shown in the illustration with the end of a screwdriver to remove the front pillar garnish clip.
  
  Note
  
  If the front pillar garnish clip is damaged, replace it with a new one.

*1	Adhesive Tape
*2	Protective Cover
*3	Curtain Shield Airbag Assembly LH

Protect the curtain shield airbag assembly LH.

Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

Note

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish assembly LH is removed.

REMOVE FRONT PILLAR GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE OUTER LAP BELT ANCHOR COVER
Tech Tips

Use the same procedure for both outer lap belt anchor covers.
1. Detach the 2 claws and guide and remove the outer lap belt anchor cover.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
1. Remove the bolt and disconnect the front seat outer belt assembly LH.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE LOWER CENTER PILLAR GARNISH LH
1. Pull both sides of the lower center pillar garnish LH outward to detach the 2 claws.
2. Detach the 4 clips and remove the lower center pillar garnish LH.
REMOVE LOWER CENTER PILLAR GARNISH RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE CENTER PILLAR GARNISH ASSEMBLY LH
1. Remove the 2 clips.
2. Detach the clip.
3. Pass the front seat outer belt floor anchor through the center pillar garnish assembly LH, and remove the center pillar garnish LH.
REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE NO. 3 BATTERY SERVICE COVER BOARD (for Power Seat)

Click here
REMOVE NO. 2 BATTERY SERVICE COVER BOARD (for Power Seat)

Click here
REMOVE UPPER DECK TRIM SIDE BOARD LH
1. Remove the bolt.
2. Detach the 10 claws and guide and remove the upper deck trim side board LH.
REMOVE UPPER DECK TRIM SIDE BOARD RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE ROPE HOOK ASSEMBLY
Tech Tips

Use the same procedure for both rope hook assemblies.
1. *1 Protective Tape
  
  Using a screwdriver, detach the 2 claws and open the cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Remove the bolt and rope hook assembly.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
Tech Tips

Use the same procedure for all luggage hold belt striker assemblies.
1. Remove the bolt and luggage hold belt striker assembly.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
1. for LH Side:
  1. Using a screwdriver, push in the claw and turn the No. 1 luggage compartment trim hook in the direction indicated by the arrow shown in the illustration.
    
    Tech Tips
    
    Tape the screwdriver tip before use.
  2. Pull the No. 1 luggage compartment trim hook in the direction indicated by the arrow in the illustration to detach the claw and guide and remove the No. 1 luggage compartment trim hook.
    
    *1 Protective Tape - -
2. for RH Side:
  1. Using a screwdriver, push in the claw and turn the No. 1 luggage compartment trim hook in the direction indicated by the arrow shown in the illustration.
    
    Tech Tips
    
    Tape the screwdriver tip before use.
  2. Pull the No. 1 luggage compartment trim hook in the direction indicated by the arrow in the illustration to detach the claw and guide and remove the No. 1 luggage compartment trim hook.
    
    *1 Protective Tape - -
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
1. Detach the 5 claws, 2 clips and 2 guides.
2. Disconnect the connectors and remove the deck trim side panel assembly LH.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH
1. Detach the 7 clips and remove the inner roof side garnish assembly LH.
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE VISOR BRACKET COVER
Tech Tips

Use the same procedure for both visor bracket covers.
1. Using moulding remover A, detach the 4 claws and remove the visor bracket cover.
REMOVE VISOR ASSEMBLY LH
1. *1 Visor Holder
  
  Disconnect the visor assembly LH from the visor holder.
2. Remove the 2 screws and visor assembly LH.
REMOVE VISOR ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE VISOR HOLDER
Tech Tips

Use the same procedure for both visor holders.
1. Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.
2. Detach the 2 claws and remove the visor holder.
REMOVE ASSIST GRIP SUB-ASSEMBLY
Tech Tips

Use the same procedure for both assist grip sub-assemblies.
1. *1 Protective Tape
  
  Put protective tape around the assist grip covers.
2. Using a clip remover, detach the 4 claws and remove the 2 assist grip covers.
3. Detach the 2 clips and remove the assist grip sub-assembly.
4. Remove the 2 clips from the vehicle body.
REMOVE REAR ASSIST GRIP ASSEMBLY LH
1. *1 Protective Tape
  
  Put protective tape around the assist grip covers.
2. Using a clip remover, detach the 4 claws and remove the 2 assist grip covers.
3. Detach the 2 clips and remove the rear assist grip assembly LH.
4. Remove the 2 clips from the vehicle body.
REMOVE REAR ASSIST GRIP ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE MAP LIGHT ASSEMBLY

Click here
REMOVE SPOT LIGHT ASSEMBLY

Click here
REMOVE SEAT BELT ANCHOR COVER
1. Detach the 2 claws, 3 clips and 2 guides and remove the seat belt anchor cover.
REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror, w/o Lane Departure Alert System)

Click here
REMOVE RAIN SENSOR COVER (w/ EC Mirror, w/o Lane Departure Alert System)

Click here
REMOVE NO. 1 LANE RECOGNITION COVER (w/ EC Mirror, w/ Lane Departure Alert System)

Click here
REMOVE ROOF HEADLINING ASSEMBLY (for Normal Roof)
1. Disconnect the connectors and detach the clamps from the front pillar LH.
2. Disconnect the connectors and detach the clamps from the front pillar RH.
3. for LHD:
  1. w/ EC Mirror, w/o Lane Departure Alert System:
    
    Disconnect the connectors.
  2. w/ EC Mirror, w/ Lane Departure Alert System:
    
    Disconnect the connectors.
4. for RHD:
  1. w/ EC Mirror, w/o Lane Departure Alert System:
    
    Disconnect the connectors.
  2. w/ EC Mirror, w/ Lane Departure Alert System:
    
    Disconnect the connectors.
5. Disconnect the connector from the rear pillar RH.
6. for Type A:
  1. Detach the 3 clips.
  2. Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
    
    Note
    
    Make sure wrinkles do not form in the roof headlining assembly during removal.
    
    Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
    
    Do not damage the roof headlining assembly or vehicle interior.
7. for Type B:
  1. Detach the 3 clips.
  2. Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
    
    Note
    
    Make sure wrinkles do not form in the roof headlining assembly during removal.
    
    Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
    
    Do not damage the roof headlining assembly or vehicle interior.
REMOVE ROOF HEADLINING ASSEMBLY (for Sliding Roof)
1. Disconnect the connectors and detach the clamps from the front pillar LH.
2. Disconnect the connectors and detach the clamps from the front pillar RH.
3. Disconnect the drive gear connector.
4. for LHD:
  1. w/ EC Mirror, w/o Lane Departure Alert System:
    
    Disconnect the connectors.
  2. w/ EC Mirror, w/ Lane Departure Alert System:
    
    Disconnect the connectors.
5. for RHD:
  1. w/ EC Mirror, w/o Lane Departure Alert System:
    
    Disconnect the connectors.
  2. w/ EC Mirror, w/ Lane Departure Alert System:
    
    Disconnect the connectors.
6. Disconnect the connector from the rear pillar RH.
7. for Type A:
  1. Detach the 3 clips, 8 fasteners and guide.
    
    *1 Fastener *2 Guide
  2. Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
    
    Note
    
    Make sure wrinkles do not form in the roof headlining assembly during removal.
    
    Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
    
    Do not damage the roof headlining assembly or vehicle interior.
8. for Type B:
  1. Detach the 3 clips, 8 fasteners and guide.
    
    *1 Fastener *2 Guide
  2. Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
    
    Note
    
    Make sure wrinkles do not form in the roof headlining assembly during removal.
    
    Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
    
    Do not damage the roof headlining assembly or vehicle interior.
REMOVE ROOF HEADLINING ASSEMBLY (for Glass Roof)
1. Disconnect the connectors and detach the clamps from the front pillar LH.
2. Disconnect the connectors and detach the clamps from the front pillar RH.
3. for LHD:
  1. w/ EC Mirror, w/o Lane Departure Alert System:
    
    Disconnect the connectors.
  2. w/ EC Mirror, w/ Lane Departure Alert System:
    
    Disconnect the connectors.
4. for RHD:
  1. w/ EC Mirror, w/o Lane Departure Alert System:
    
    Disconnect the connectors.
  2. w/ EC Mirror, w/ Lane Departure Alert System:
    
    Disconnect the connectors.
5. Disconnect the connector from the rear pillar RH.
6. Detach the 3 clips, 14 fasteners and guide.
  
  *1 Fastener *2 Guide
7. Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.
  Note
  
  Make sure wrinkles do not form in the roof headlining assembly during removal.
  
  Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
  
  Do not damage the roof headlining assembly or vehicle interior.
REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
1. Detach the 6 guides and remove the front shoulder belt anchor plate sub-assembly LH.
REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

Click here
REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR SIDE RAIL SPACER LH
1. Remove the 2 bolts.
2. Detach the claw and remove the rear side rail spacer LH.
REMOVE REAR SIDE RAIL SPACER RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE REAR NO. 2 SIDE RAIL SPACER LH
1. Remove the 2 bolts.
2. Detach the 2 claws and remove the rear No. 2 side rail spacer LH.
REMOVE REAR NO. 2 SIDE RAIL SPACER RH

Tech Tips

Use the same procedure described for the LH side.

*1	Claw A
*2	Claw B

*1	Claw A
*2	Claw B

*1	Claw A
*2	Claw B

*1	Claw A
*2	Claw B