LOWER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

PROCEDURE

1. TABLE OF BOLT, SCREW AND CLIP

   Tech Tips

   All bolts, screws, and clips relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

   

2. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

   
   

   1. Disable the autoaway/return function by changing the customize parameter.

      Click here

      CAUTION:

      Record the current customize parameter setting (whether the autoaway/return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the autoaway/return function to be disabled when the power switch is turned off.

   2. Turn the power switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

   3. Turn the power switch off.

3. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Spare Tire)

   Click here

4. REMOVE REAR DECK FLOOR BOX (w/ Spare Tire)

   Click here

5. REMOVE DECK FLOOR BOX LH (w/ Spare Tire)

   Click here

6. PRECAUTION

   Note

   After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work.

   Click here

7. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

   CAUTION:

   Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

   Note

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

   Click here

   
   

   1. 

      w/o Spare tire:

      Detach the 2 claws and remove the battery service cover.

8. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

   Click here

9. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

   Click here

10. REMOVE COWL SIDE TRIM BOARD RH

    Click here

11. REMOVE CONSOLE ARMREST ASSEMBLY

    Click here

12. REMOVE UPPER REAR CONSOLE PANEL

    Click here

13. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH

    Click here

14. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH

    Click here

15. REMOVE INSTRUMENT SIDE PANEL LH

    Click here

16. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

17. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

18. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    Click here

19. REMOVE NO. 1 SWITCH HOLE BASE

    Click here

20. REMOVE INSTRUMENT SIDE PANEL RH

    Click here

21. REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

22. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    Click here

23. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

    Click here

24. REMOVE COMBINATION METER ASSEMBLY

    Click here

25. REMOVE MULTI-DISPLAY ASSEMBLY

    Click here

26. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

    Click here

27. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    
    

    1. Disconnect the front door opening trim weatherstrip LH so that the front pillar garnish assembly LH can be removed.

28. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    
    

    1. Disconnect the front door opening trim weatherstrip RH so that the front pillar garnish assembly RH can be removed.

29. REMOVE FRONT PILLAR GARNISH ASSEMBLY LH

    Click here

30. REMOVE FRONT PILLAR GARNISH ASSEMBLY RH

    Click here

31. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

32. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

33. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

    Click here

34. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

    Click here

35. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY

    Click here

36. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

37. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

    Click here

38. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

    Click here

39. REMOVE INNER NO. 1 INSTRUMENT PANEL BRACE COVER LH

    Click here

40. REMOVE INNER NO. 1 INSTRUMENT PANEL BRACE COVER RH

    Click here

41. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY

    Click here

42. REMOVE CONSOLE BOX POCKET (w/o Wireless Charger)

    Click here

43. REMOVE CONSOLE BOX CARPET

    Click here

44. REMOVE CONSOLE BOX ASSEMBLY

    Click here

45. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    
    

    1. 

       Pull the air conditioning control assembly in the direction indicated by the arrows shown in the illustration to detach the 6 clips.

    2. Disconnect the connectors and remove the air conditioning control assembly.

46. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

    
    

    1. 

       Place your hand as shown in the illustration, and then pull the center instrument panel register assembly in the direction indicated by the arrow shown in the illustration to detach the 4 clips and remove the center instrument panel register assembly.

47. REMOVE CENTER HEATER TO REGISTER DUCT

    
    
    1. 

       *1

       Clip <C>

       Remove the 2 clips <C>.

    2. Detach the 2 claws and remove the center heater to register duct.

48. REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio)

    Click here

49. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    
    

    1. 

       for LHD:

       
       

       1. Using moulding remover A, detach the 3 claws and guide.

       2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

    2. 

       for RHD:

       
       

       1. Using moulding remover A, detach the 2 claws and guide.

       2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

50. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    Click here

51. REMOVE COWL SIDE TRIM BOARD LH

    Click here

52. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

53. REMOVE TELEMATICS TRANSCEIVER

    Click here

54. REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX

    Click here

55. REMOVE NO. 2 INSTRUMENT PANEL HOLE COVER (for RHD)

    
    
    1. 

       *1	Protective Tape

       Put protective tape around the No. 2 instrument panel hole cover.

    2. Using a screwdriver, detach the 2 claws and 2 guides and remove the No. 2 instrument panel hole cover.

       Tech Tips

       Tape the screwdriver tip before use.

56. REMOVE INSTRUMENT PANEL HOLE COVER (for RHD)

    
    
    1. 

       *1	Screws <A> or <B>

       Remove the 2 screws <A> or <B> and instrument panel hole cover.

57. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

    
    

    1. 

       Detach the claw and remove the glove compartment door stopper sub-assembly.

58. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    
    

    1. for LHD:

       
       

       1. Detach the clamps.

       2. Remove the 2 bolts <D>.

       3. Remove the 9 bolts <F> or <G>.

       4. Remove the screw <E>.

       5. Disconnect the connector and room temperature sensor.

       6. Detach the 2 claws and disconnect the DLC3.

       7. Detach the claw and 2 guides and disconnect the hood lock control lever sub-assembly and remove the lower instrument panel sub-assembly.

          

          *1	Bolt <D>	*2	Bolt <F> or <G>
          *3	Screw <E>	*4	Connector
          *5	Room Temperature Sensor	*6	DLC3
          *7	Guide	*8	Hood Lock Control Lever Sub-assembly

    2. for RHD:

       
       

       1. Detach the clamps.

       2. Remove the 2 bolts <D>.

       3. Remove the 9 bolts <F> or <G>.

       4. Remove the screw <E>.

       5. Disconnect the connector and room temperature sensor.

       6. Detach the 2 claws and disconnect the DLC3.

       7. Detach the claw and 2 guides and disconnect the hood lock control lever sub-assembly and remove the lower instrument panel sub-assembly.

          

          *1	Bolt <D>	*2	Bolt <F> or <G>
          *3	Screw <E>	*4	Connector
          *5	Room Temperature Sensor	*6	DLC3
          *7	Guide	*8	Hood Lock Control Lever Sub-assembly