FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

PROCEDURE


  1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. B002HMIC01

      Connect the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.

    2. Tighten the bolts in the order shown in the illustration to install the front shoulder belt anchor adjuster assembly LH.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Attach the 6 guides to install the front shoulder belt anchor plate sub-assembly LH.

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


    1. Attach the 2 guides and install the front seat outer belt assembly LH with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
    2. B002IL1C01
      *1 Locking Button

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    3. Connect the connector.

    4. Connect the shoulder anchor of the front seat outer belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. B002KY4C01
      *1 Bolt A

      Connect the floor anchor of the front seat outer belt assembly LH with the bolt A.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. Check that the ELR locks.

      Note

      The check should be performed with the front seat outer belt assembly LH installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

    7. B002KY4C01
      *1 Bolt A

      Remove the bolt A and disconnect the floor anchor of the front seat outer belt assembly LH.

  4. INSTALL CENTER PILLER GARNISH ASSEMBLY LH

    Click here

  5. INSTALL LOWER CENTER PILLAR GARNISH LH

    Click here

  6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Install the front door opening trim weatherstrip LH.

  7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Install the rear door opening trim weatherstrip LH.

  8. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. Connect the floor anchor of the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  9. INSTALL LAP BELT OUTER ANCHOR COVER


    1. Attach the guide, 2 claws and install the lap belt anchor cover.

  10. INSTALL REAR DOOR SCUFF PLATE LH

    Click here

  11. INSTALL DOOR SCUFF PLATE ASSEMBLY LH

    Click here

  12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  13. CHECK SRS WARNING LIGHT

    Click here

  14. INSTALL DECK FLOOR BOX LH (w/ Spare Tire)

    Click here

  15. INSTALL REAR DECK FLOOR BOX (w/ Spare Tire)

    Click here

  16. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  17. INSTALL DECK BOARD ASSEMBLY

    Click here