FRONT SEAT OUTER BELT ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

Tech Tips

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a seat belt (with a seat belt pretensioner), always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the SERVICE DEPARTMENT of the distributor.

PROCEDURE


  1. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Installed in Vehicle)

    CAUTION:


    • Use gloves and safety glasses when handling a front seat outer belt with a deployed pretensioner.

    • Always wash your hands with water after completing the operation.

    • Do not apply water, etc. to a front seat outer belt with a deployed pretensioner.

    • When deploying the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

    Note


    • When disposing of a front seat outer belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.

    • Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.

    • The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.

    • When deploying a front seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the front seat outer belt.

    • Be sure to follow the procedure listed below when deploying the seat belt pretensioner.


    1. B002KSLN01

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the seat belt pretensioner, always use the specified SST.


      1. B002JX3C11
        *1 Battery

        Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        Tech Tips

        At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.

      2. B002K6HN01

        Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

        CAUTION:

        If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.

    2. Disconnect the front seat outer belt pretensioner connector.


      1. Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      2. Remove the lower center pillar garnish.

        Click here

      3. Connect the floor anchor of the front seat outer belt assembly with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      4. B002IG4C01
        *1 Protective Tape
        *2 Locking Button

        for Driver Side, Front Passenger Seat Belt without Selectable Force Limiter:

        Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

      5. Disconnect the connector.

      6. B002L3OC01
        *1 Protective Tape
        *2 Locking Button

        for Front Passenger Seat Belt with Selectable Force Limiter:

        Using a screwdriver, pull out the 2 locking buttons in the direction shown by the arrow in the illustration to release the lock and disconnect the pretensioner connector and selectable force limiter connector as shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

      7. Disconnect the connector.

    3. for Driver Side, Front Passenger Seat Belt without Selectable Force Limiter:

      SST
      09082-00700

      1. B002KX9E01

        Connect SST.


        1. Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

          Note

          To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

        2. Move SST at least 10 m (33 ft.) away from the front of the vehicle.

        3. Close all the doors and windows of the vehicle.

          Note

          Do not damage the SST wire harness.

      2. B002IQCC24
        *a 10 m or more

        Move SST at least 10 m (33 ft.) away from the front of the vehicle.

      3. Close all the doors and windows of the vehicle.

        Note

        Do not damage the SST wire harness.

      4. Deploy the front seat outer belt pretensioner.


        1. Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

        2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

        3. Press the SST deployment switch to deploy the front seat outer belt pretensioner.

          Tech Tips

          The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

    4. B002JA6

      Dispose of the front seat outer belt assembly.


      1. Remove the front seat outer belt assembly and SST.

      2. Place the front seat outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

        CAUTION:


        • The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

        • Use gloves and safety glasses when handling a front seat outer belt with a pretensioner that has been deployed.

        • Always wash your hands with water after completing the operation.

        • Do not apply water, etc. to a front seat outer belt assembly with a pretensioner that has been deployed.

        Tech Tips

        When scrapping a vehicle, deploy the front seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.

    5. for Front Passenger Seat Belt with Selectable Force Limiter:

      SST
      09082-00700

      1. B002KX9E01

        Connect SST.


        1. Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

          Note

          To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

        2. Move SST at least 10 m (33 ft.) away from the front of the vehicle.

        3. Close all the doors and windows of the vehicle.

          Note

          Do not damage the SST wire harness.

      2. B002IQCC24
        *a 10 m or more

        Move SST at least 10 m (33 ft.) away from the front of the vehicle.

      3. Close all the doors and windows of the vehicle.

        Note

        Do not damage the SST wire harness.

      4. Deploy the front seat outer belt pretensioner.


        1. Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

        2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

        3. Press the SST deployment switch to deploy the front seat outer belt pretensioner.

          Tech Tips

          The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

      5. Disconnect SST.

        CAUTION:

        The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

      6. Connect SST.

        SST
        09082-00700

        1. B002H1UN01

          Connect 2 SST, and then connect them to the front seat outer belt selectable force limiter.

          Note

          To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the selectable force limiter connector.

        2. B002IQCC10
          *a 10 m or more

          Move SST at least 10 m (33 ft.) away from the front of the vehicle.

        3. Close all the doors and windows of the vehicle.

          Note

          Do not damage the SST wire harness.

      7. Deploy the front seat outer belt selectable force limiter.


        1. Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

        2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

        3. Press the SST deployment switch to deploy the front seat outer belt selectable force limiter.

          Tech Tips

          The seat belt selectable force limiter will deploy at the same time as the LED of SST illuminates.

  2. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY RH (When not Installed in Vehicle)

    CAUTION:


    • Use gloves and safety glasses when handling a front seat outer belt with a deployed pretensioner.

    • Always wash your hands with water after completing the operation.

    • Do not apply water, etc. to a front seat outer belt with a deployed pretensioner.

    • When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

    Note


    • When disposing of a front seat outer belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.

    • Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.

    • The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.

    • When deploying a front seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the front seat outer belt.

    • Be sure to follow the procedure listed below when deploying the seat belt pretensioner.


    1. B002KSLN01

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the seat belt pretensioner, always use the specified SST.


      1. B002JX3C11
        *1 Battery

        Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        Tech Tips

        At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.

      2. B002K6HN01

        Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

        CAUTION:

        If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Remove the front seat outer belt assembly.

      Click here

    4. B002HJKC02
      *a Cut
      *b 100 mm

      Wind the seat belt webbing with the retractor.

    5. When the seat belt webbing is sufficiently wound, cut the seat belt webbing approximately 100 mm (3.94 in.) from the retractor as shown in the illustration.

      Tech Tips

      The retractor resistance increases in correlation with how much the seat belt webbing is wound.

    6. for Driver Side, Front Passenger Seat Belt without Selectable Force Limiter:

      SST
      09082-00700

      1. B002KX9E01

        Connect SST.


        1. Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

          Note

          To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

        2. B002JWGE01

          Place the front seat outer belt on the ground and cover it with a tire and wheel assembly.

          Note


          • Position the front seat outer belt assembly as shown in the illustration.

          • Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.

        3. Position and hold SST at least 10 m (33 ft.) away from the wheel.

          Note

          Do not damage the SST wire harness.

      2. Deploy the front seat outer belt pretensioner.


        1. B002JISC01
          *a 10 m or more

          Check that no one is within a 10 m (33 ft.) radius of the wheel.

        2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        3. Press the SST deployment switch to deploy the seat belt pretensioner.

          Tech Tips

          The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

    7. B002JA6

      Dispose of the front seat outer belt assembly.


      1. Remove the wheel and SST.

      2. Place the front seat outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

        CAUTION:


        • The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

        • Use gloves and safety glasses when handling a front seat outer belt with a pretensioner that has been deployed.

        • Always wash your hands with water after completing the operation.

        • Do not apply water, etc. to a front seat outer belt assembly with a pretensioner that has been deployed.

        Tech Tips

        When scrapping a vehicle, deploy the front seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.

    8. for Front Passenger Seat Belt with Selectable Force Limiter:

      SST
      09082-00700

      1. Connect SST.


        1. B002ILUN01

          Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

          Note

          To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.

        2. B002KHAN01

          Place the front seat outer belt on the ground and cover it with a tire and wheel assembly.

          Note


          • Position the front seat outer belt assembly as shown in the illustration.

          • Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.

        3. Position and hold SST at least 10 m (33 ft.) away from the wheel.

          Note

          Do not damage the SST wire harness.

      2. Deploy the front seat outer belt pretensioner.


        1. B002JISC01
          *a 10 m or more

          Check that no one is within a 10 m (33 ft.) radius of the wheel.

        2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        3. Press the SST deployment switch to deploy the seat belt pretensioner.

          Tech Tips

          The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.

      3. Disconnect SST.

        CAUTION:

        The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

      4. Connect SST.


        1. B002H1UN01

          Connect 2 SST, and then connect them to the front seat outer belt selectable force limiter.

          Note

          To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the selectable force limiter connector.

        2. B002IECN01

          Place the front seat outer belt on the ground and cover it with a tire and wheel assembly.

          Note


          • Position the front seat outer belt assembly as shown in the illustration.

          • Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.

        3. Position and hold SST at least 10 m (33 ft.) away from the wheel.

          Note

          Do not damage the SST wire harness.

      5. Deploy the front seat outer belt selectable force limiter.


        1. B002JISC01
          *a 10 m or more

          Check that no one is within a 10 m (33 ft.) radius of the wheel.

        2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

        3. Press the SST deployment switch to deploy the seat belt pretensioner.

          Tech Tips

          The seat belt selectable force limiter will deploy at the same time as the LED of SST illuminates.