FRONT SEAT ASSEMBLY(for Manual Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY LH


    1. Place the front seat assembly in the cabin.

      Note


      • 2 or more people are required when inserting the front seat assembly into the vehicle.

      • Be careful not to damage the vehicle body.

      Tech Tips

      for Driver Side:

      When placing the front seat assembly into the vehicle, pass it through under the steering wheel.

    2. Tilt the front seat assembly LH toward the rear of the vehicle.

      Note

      Be careful not to damage the vehicle body.

    3. for Driver Side:


      1. Connect the connector to the front seat airbag assembly under the front seat assembly.


        1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

          B002HLWC04
          *1 Yellow CPA - -
          *a Correct *b Incorrect

        2. Hold the sides of the yellow CPA and push in the connector in the direction indicated by the arrow until a click sound is heard to connect the connector.

          Note


          • Be careful not to damage the side airbag connector or wire harness.


          • When connecting the connector, make sure to push it straight in.


          • Do not hold any parts other than the yellow CPA when connecting the connector.


          • If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.

    4. Connect the 2 connectors.

    5. Attach the clamp to connect the wire harness.

    6. for Front Passenger Side:


      1. Connect the connector to the front seat airbag assembly under the front seat assembly.


        1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

          B002HLWC04
          *1 Yellow CPA - -
          *a Correct *b Incorrect

        2. Hold the sides of the yellow CPA and push in the connector in the direction indicated by the arrow until a click sound is heard to connect the connector.

          Note


          • Be careful not to damage the side airbag connector or wire harness.


          • When connecting the connector, make sure to push it straight in.


          • Do not hold any parts other than the yellow CPA when connecting the connector.


          • If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.

      2. Connect the connector of the front seat cushion airbag assembly RH.

    7. Connect the 2 connectors.

    8. Attach the clamp to connect the wire harness.

    9. Align the pin of the front seat adjuster with the hole in the vehicle.

    10. Temporarily install the front seat assembly with the 4 bolts.

    11. Operate the seat track adjusting handle to move the seat to the rearmost position.

    12. B002HZHN01

      Tighten the 2 bolts in the order indicated in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    13. Operate the seat track adjusting handle to move the seat to the foremost position.

    14. B002HYHN01

      Tighten the 2 bolts in the order indicated in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  2. INSTALL FRONT SEAT REAR INNER TRACK COVER LH


    1. Attach the 2 claws to install the front seat rear inner track cover LH.

  3. INSTALL FRONT SEAT REAR OUTER TRACK COVER LH


    1. Attach the 2 claws to install the front seat rear outer track cover LH.

  4. INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH


    1. Operate the seat track adjusting handle to move the seat to the rearmost position.

    2. Attach the 2 claws to install the front seat inner track bracket cover LH.

  5. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH


    1. Attach the 2 claws to install the front seat outer track bracket cover LH.

  6. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly.

  7. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here


    1. Connect the cable to the auxiliary battery negative (-) terminal and tighten the nut.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    2. w/o Spare Tire:

      Attach the 2 claws to install the battery service cover.

  8. INSTALL DECK FLOOR BOX LH (w/ Spare Tire)

    Click here

  9. INSTALL REAR DECK FLOOR BOX (w/ Spare Tire)

    Click here

  10. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  11. CHECK SRS WARNING LIGHT

    Click here

  12. INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

    Click here