FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) Power Seat Position is not Memorized

DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch signals from the outer mirror control ECU assembly (for Driver Side) via CAN communication. If the seat memory SET switch is being pressed when one of the M1, M2 or M3 switches is pressed, or if one of the M1, M2 or M3 switches is pressed within 3 seconds of pressing the seat memory SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the front power seat switch (for Driver Side). After receiving the request signal, the front power seat switch (for Driver Side) memorizes the location data of each motor.

WIRING DIAGRAM

B002K43E05

CAUTION / NOTICE / HINT

Note


  • The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

    Click here

  • The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

    If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

  • The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

    If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

PROCEDURE


  1. CHECK FRONT POWER SEAT OPERATION


    1. Check that each function of the power seat operates normally by using the front power seat switch (for Driver Side).

      Click here

      OK
      Each function of the power seat operates normally using the front power seat switch (for Driver Side).
      Result
      Proceed to
      OK
      NG

    NG

    GO TO PROBLEM SYMPTOMS TABLE Click here

    OK

  2. READ VALUE USING GTS (SEAT MEMORY SWITCH1, SEAT MEMORY SWITCH2, SEAT MEMORY SWITCH3, SEAT MEMORY SET SW)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Mirror L*1 or Mirror R*2 / Data List.


      • *1: for LHD

      • *2: for RHD

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Mirror L > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Seat Memory Switch1 M1 switch ON or OFF

      ON: M1 switch on

      OFF: M1 switch off

      		 -
      Seat Memory Switch2 M2 switch ON or OFF

      ON: M2 switch on

      OFF: M2 switch off

      		 -
      Seat Memory Switch3 M3 switch ON or OFF

      ON: M3 switch on

      OFF: M3 switch off

      		 -
      Seat Memory Set SW SET switch ON or OFF

      ON: SET switch on

      OFF: SET switch off

      		 -

      Body Electrical > Mirror L > Data List
      Tester Display
      Seat Memory Switch1
      Seat Memory Switch2
      Seat Memory Switch3
      Seat Memory Set SW

      Body Electrical > Mirror R > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Seat Memory Switch1 M1 switch ON or OFF

      ON: M1 switch on

      OFF: M1 switch off

      		 -
      Seat Memory Switch2 M2 switch ON or OFF

      ON: M2 switch on

      OFF: M2 switch off

      		 -
      Seat Memory Switch3 M3 switch ON or OFF

      ON: M3 switch on

      OFF: M3 switch off

      		 -
      Seat Memory Set SW SET switch ON or OFF

      ON: SET switch on

      OFF: SET switch off

      		 -

      Body Electrical > Mirror R > Data List
      Tester Display
      Seat Memory Switch1
      Seat Memory Switch2
      Seat Memory Switch3
      Seat Memory Set SW
      OK
      The GTS display changes correctly in response to the switch operation.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT SEAT MEMORY SWITCH Click here

    OK

  3. PERFORM ACTIVE TEST USING GTS (BUZZER)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Driver Seat / Active Test.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Driver Seat > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Buzzer Buzzer operation OFF/ON -

      Body Electrical > Driver Seat > Active Test
      Tester Display
      Buzzer
      OK
      Buzzer sounds/stops normally using the GTS operation.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT POWER SEAT SWITCH (for Driver Side) Click here

    OK

  4. REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (for Driver Side)


    1. Replace the outer mirror control ECU assembly (for Driver Side) with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION


    1. Check that the seat position memory and restoring function.

      Click here

      OK
      Seat position memory and restoring function operate normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER MIRROR CONTROL ECU ASSEMBLY [for Driver Side] WAS DEFECTIVE)

    NG

    REPLACE FRONT POWER SEAT SWITCH (for Driver Side) Click here

  6. INSPECT SEAT MEMORY SWITCH


    1. Remove the seat memory switch.

      Click here

    2. Inspect the seat memory switch.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SEAT MEMORY SWITCH Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY [for Driver Side] - SEAT MEMORY SWITCH AND BODY GROUND)


    • *1: for LHD

    • *2: for RHD


    1. Disconnect the M5*1 or L5*2 outer mirror control ECU assembly (for Driver Side) connector.

    2. Disconnect the M12*1 or L8*2 seat memory switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      M5-1 (MM) - M12-1 (MRY) Always Below 1 Ω
      M5-1 (MM) or M12-1 (MRY) - Body ground Always 10 kΩ or higher
      M5-2 (M1) - M12-2 (M1) Always Below 1 Ω
      M5-2 (M1) or M12-2 (M1) - Body ground Always 10 kΩ or higher
      M5-3 (M2) - M12-3 (M2) Always Below 1 Ω
      M5-3 (M2) or M12-3 (M2) - Body ground Always 10 kΩ or higher
      M5-4 (M3) - M12-4 (M3) Always Below 1 Ω
      M5-4 (M3) or M12-4 (M3) - Body ground Always 10 kΩ or higher
      M5-7 (GND) - Body ground Always Below 1 Ω
      M12-5 (E) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      L5-1 (MM) - L8-1(MRY) Always Below 1 Ω
      L5-1 (MM) or L8-1(MRY) - Body ground Always 10 kΩ or higher
      L5-2 (M1) - L8-2 (M1) Always Below 1 Ω
      L5-2 (M1) or L8-2 (M1) - Body ground Always 10 kΩ or higher
      L5-3 (M2) - L8-3 (M2) Always Below 1 Ω
      L5-3 (M2) or L8-3 (M2) - Body ground Always 10 kΩ or higher
      L5-4 (M3) - L8-4 (M3) Always Below 1 Ω
      L5-4 (M3) or L8-4 (M3) - Body ground Always 10 kΩ or higher
      L5-7 (GND) - Body ground Always Below 1 Ω
      L8-5 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR