ENTRY AND START SYSTEM(for Entry Function) CUSTOMIZE PARAMETERS


  1. CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Wireless Door Lock, Entry & Start or Warning.

      5. Select the setting by referring to the table below.


        Wireless Door Lock
        Tester Display Description Default Setting ECU
        Wireless Control Function that turns the wireless door lock control system on or off ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
        Hazard Answer Back

        When the doors are locked by the entry lock function, the hazard warning lights flash once.

        When the doors are unlocked by the entry lock function, the hazard warning lights flash twice.

        ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
        Open Door Warning The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.*1 ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
        Auto Lock Time Function that regulates the interval between unlocking and automatic relocking of doors. 30 s 00:30 s,01:60 s,10:120 s Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Resp Wireless buzzer response.*2 ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Vol Buzzer answer-back volume.*2 Level5 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 Main body ECU (Multiplex network body ECU)

        • *1: w/ Door Ajar Warning Buzzer Function

        • *2: w/ Wireless Door Lock Buzzer Answer-back Function


        Warning
        Tester Display Description Default Setting ECU
        Key Low Battery Warning Enables or disables the sounding of the buzzer when the transmitter battery is low and the power switch is turned off after being on (IG) for 20 minutes or more. ON 0:OFF,1:ON Certification ECU (Smart key ECU assembly)

        Entry & Start
        Tester Display Description Default Setting ECU
        Park Wait Time Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed. 2.5s 00:0.5s,01:1.5s,10:2.5s,11:5s Certification ECU (Smart key ECU assembly)
        Ignition Available Area Function that sets the area that the key must be in before the power switch can be operated. Front or All* 00:Front,01:All Certification ECU (Smart key ECU assembly)
        Back Door Opening Operation Function that sets the back door when the user is carrying the electrical key transmitter sub-assembly and presses the back door opener switch assembly (open switch). Long 00:Long,01:Twice,10:OFF Certification ECU (Smart key ECU assembly)
        Door Unlock Mode2 Function that sets which doors are unlocked by the entry unlock function. Driver or All* 0:All,1:Driver Certification ECU (Smart key ECU assembly)
        Auto Entry Cancel SW Function that enables or disables the entry and start system. OFF 0:OFF,1:ON Certification ECU (Smart key ECU assembly)
        Touch Activation Over Threshold The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active or Not Active* 0:Active,1:Not Active Certification ECU (Smart key ECU assembly)
        Engine Start Indicator Function that turns the entry warning light on the combination meter assembly on or off. ON 0:OFF,1:ON Certification ECU (Smart key ECU assembly)

        • *: Default setting differs depending on the country.

    2. Customizing with the multi-display


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Select doors to unlock Driver's door or All doors*1 Function that sets which doors are unlocked by the entry unlock function. All doors or Driver's door Certification ECU (Smart key ECU assembly)
        Entry and start system On Function that enables or disables the entry and start system. On or Off Certification ECU (Smart key ECU assembly)
        Lock/unlock feedback lights On

        When the doors are locked by the entry lock function, the hazard warning lights flash once.

        When the doors are unlocked by the entry lock function, the hazard warning lights flash twice.

        On or Off Main body ECU (Multiplex network body ECU)
        Lock/unlock feedback-Tone*2 5 Buzzer answer-back volume. Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

        • *1: Default setting differs depending on the country.

        • *2: w/ Wireless Door Lock Buzzer Answer-back Function

    3. Entry unlock mode switching function (manual operation)


      1. The following entry unlock modes can be selected when using the entry unlock mode switching function.


        • All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.

        • Driver door unlock mode: When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.

      2. When customizing through manual operation:


        1. Turn the power switch off.

        2. Cancel the intrusion sensor (theft warning ultrasonic sensor).

          *: w/ Intrusion Sensor Cancel Switch

        3. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock switches of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.

        4. Check the current setting.

          Tech Tips


          • The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

          • The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.

            Currently Selected Mode Answer-back (Wireless Buzzer) Answer-back (Buzzer in Combination Meter Assembly)
            All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once
            Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once
        5. Release the lock and unlock switches of the electrical key transmitter sub-assembly.

        6. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock switches of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

          Tech Tips

          Repeat the procedure as necessary to select the desired mode.

        7. Unlock the doors with the wireless operation, and then open any door.

          B002I4CE01
    4. Entry cancel function (manual operation)

      Tech Tips

      While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the power switch.


      1. The following functions are disabled when the entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Push-button start function

        3. Key lock-in prevention function

        4. Entry warning functions

      2. When canceling the entry and start system through manual operation:


        1. Make sure the following conditions are met:


          • The power switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

      3. Press the unlock switch of the electrical key transmitter sub-assembly.

      4. Open the driver door within 5 seconds of completing the step above (driver door: closed → opened).

      5. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        Note

        If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      6. Perform the following procedure within 30 seconds of completing the step above.


        1. Close and open the driver door twice (driver door: open → closed → opened → closed → opened).

        2. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times.

          Note

          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        3. Close and open the driver door (driver door: open → closed → opened).

      7. Close the driver door within 5 seconds (driver door: open → closed).

      8. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

      9. Perform the following procedure to restore the entry and start system to the active state from the canceled state.


        1. Perform the procedure to cancel the entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.