FRONT DOOR LOCK INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

   
   

   1. 

      w/o Double Locking System:

      
      

      1. Attach the clamp to install the front door inside locking cable assembly LH to the front door lock assembly LH.

   2. w/ Double Locking System:

      
      

      1. 

         Attach the clamp to install the front door inside locking cable assembly LH to the front door lock assembly LH.

      2. 

         Attach the 2 guides.

      3. Attach the claw to close the cover.

2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

   
   

   1. w/o Double Locking System:

      
      

      1. 

         Attach the clamp to install the front door lock remote control cable assembly LH to the front door lock assembly LH.

   2. 

      w/ Double Locking System:

      
      

      1. Attach the clamp to install the front door lock remote control cable assembly LH to the front door lock assembly LH.

3. INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

   
   

   1. Attach the 2 guides.

   2. Attach the 2 claws to install the front door lock cover sub-assembly LH.

4. INSTALL DOOR LOCK WIRING HARNESS SEAL

   
   

   1. Install a new door lock wiring harness seal to the front door lock assembly LH.

5. INSTALL FRONT DOOR LOCK ASSEMBLY LH

   Note

   
   

   • When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

   • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

   • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.

   
   

   1. Apply MP grease to the sliding parts of the front door lock assembly LH.

   2. Insert the front door lock open rod LH into the front door lock assembly LH.

      

      *A	w/o Double Locking System	*B	w/ Double Locking System
      *1	Front Door Lock Open Rod LH	-	-
      	Upward	-	-

   3. Make sure that the front door lock open rod is securely connected to the front door lock assembly LH.

   4. Using a T30 "TORX" socket wrench, install the front door lock assembly LH with the 3 screws.

      Torque:

      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

   5. Connect the connector.

6. INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)

   Click here

7. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

   Click here

8. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

   Click here

9. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

   Click here

10. INSTALL FRONT DOOR GLASS RUN LH

    Click here

11. INSTALL FRONT DOOR SERVICE HOLE COVER LH

    Click here

12. INSTALL FRONT DOOR ARMREST SET BRACKET LH

    Click here

13. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

    Click here

14. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

15. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Click here

16. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    Click here

17. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

18. INSTALL FRONT DOOR TRIM COVER LH

    Click here

19. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

20. INSTALL DECK FLOOR BOX LH (w/ Spare Tire)

    Click here

21. INSTALL REAR DECK FLOOR BOX (w/ Spare Tire)

    Click here

22. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Spare Tire)

    Click here

23. INSTALL DECK BOARD ASSEMBLY

    Click here

24. CHECK SRS WARNING LIGHT

    Click here

25. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

26. CHECK POWER WINDOW CONTROL SYSTEM

    Click here

27. CHECK POWER DOOR LOCK CONTROL SYSTEM

    Click here