CAN COMMUNICATION SYSTEM(for RHD) ASC ECU Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
ASC ECU Communication Stop Mode

Either condition is met:


  • "ASC" is not displayed on "CAN Bus Check".

    Click here

  • Communication system DTCs (DTCs that start with U) that are output correspond to "ASC ECU Communication Stop Mode" in "DTC Combination Table".

    Click here


  • Power source circuit of stereo component equalizer assembly

  • Stereo component equalizer assembly ground circuit

  • Stereo component equalizer assembly CAN branch wire or connector

  • Stereo component equalizer assembly

WIRING DIAGRAM

A00021QE03

CAUTION / NOTICE / HINT

Note


  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Turn the power switch on (IG) and wait at least 8.2 seconds.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Operating the power switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE


  1. CHECK FOR OPEN IN CAN BUS WIRE (STEREO COMPONENT EQUALIZER ASSEMBLY BRANCH WIRE)


    1. B002JMUC06
      *a

      Front view of wire harness connector

      (to Stereo Component Equalizer Assembly)

      Disconnect the cable from the negative (-) auxiliary battery terminal.

    2. Disconnect the stereo component equalizer assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I117-4 (CANH) - I117-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
      Result
      Proceed to
      OK
      NG

    NG
    OK
  2. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY - BATTERY AND BODY GROUND)


    1. A00019GC07
      *a

      Front view of wire harness connector

      (to Stereo Component Equalizer Assembly)

      Reconnect the cable to the negative (-) auxiliary battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I117-3 (+B) - Body ground Power switch off 11 to 14 V
      I117-11 (IG) - Body ground Power switch on (IG) 11 to 14 V
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I117-1 (GND) - Body ground Always Below 1 Ω
      I117-9 (GND1) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK
    NG