AUDIO AND VISUAL SYSTEM(for 8 Speakers) OPERATION CHECK


  1. CHECK PANEL & STEERING SWITCH

    Tech Tips


    • The radio receiver assembly panel switches and steering switches are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B002IJ7

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0000UU

      Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

    4. B002JGSN01

      Panel & Steering Switch Check Mode

      Screen Description
      Display Content
      *a: Switch condition "Pushed" is displayed when any switch is pushed.
      *b: Number of switches pushed

      • Number of switches pushed at once is displayed.

      • If more than 3 switches are pushed at once, "More than 3" is displayed.
      *c: Rotary switch direction Direction of rotary switch is displayed.

      1. Operate each switch and check that the switch conditions are correctly displayed.

        Note

        When the return switch on the remote operation board is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

  2. CHECK MICROPHONE

    Tech Tips


    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B002IJ7

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0000PS

      Select "Microphone Check" from the "Function Check/Setting I" screen.

    4. B002KADN01

      Microphone Check

      Screen Description
      Display Content
      *a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
      *b: Recording switch Starts recording.
      *c: Stop switch Stops recording and playing.
      *d: Play switch Plays the recorded voice.
      *e: Recording indicator Comes on while recording.

      1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

        Tech Tips

        The microphone is active at all times when this screen is displayed.

      2. Push the recording switch and perform voice recording.

        Tech Tips


        • Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

        • While recording or playing, switches other than the stop switch cannot be pushed.

        • When no recording is present, the play switch cannot be pushed.

        • Recording will stop after 5 seconds or when the stop switch is pushed.

      3. Check that the recording indicator remains on while recording and that the recording can be played normally.

  3. CHECK VEHICLE SIGNAL

    Tech Tips


    • Vehicle signals received by the radio receiver assembly are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B002IJ7

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0000I7

      Select "Vehicle Signal" from the "Function Check/Setting I" screen.

    4. B002JE3

      Vehicle Signal Check Mode

      Screen Description
      Display Content
      Battery Auxiliary battery voltage is displayed.
      IG Power switch ON/OFF state is displayed.
      PKB Parking brake ON/OFF state is displayed.
      REV Reverse signal ON/OFF state is displayed.
      SPEED Vehicle speed is displayed in km/h.
      TAIL Tail signal (light control switch) ON/OFF state is displayed.
      ADIM/TCAN Brightness state DIM (with)/BRIGHT (without) is displayed.

      Tech Tips


      • Only items sending vehicle signals will be displayed.

      • This screen displays vehicle signals received by the radio receiver assembly.

      • This screen is updated once per second.


      1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

  4. CHECK HANDS-FREE VOICE QUALITY SETTING

    Tech Tips


    • The hands-free voice of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B002IJ7

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A00007V

      Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

    4. B002KR0C01
      *a Numeric Keypad
      *b Setting Button
      *c Reset Button

      Hands-Free Voice Quality Setting


      1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

      2. When adjusting the settings, use the numeric keypad on the screen to input the voice quality type according to the table.

        Settings
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality

        A

        (Noise)

        		 The other party hears background noise when listening to your voice. 1000 The amount of background noise the other party hears when listening to your voice is reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        B

        (Noise)

        		 The other party hears a lot of background noise when listening to your voice. 2000 The amount of background noise the other party hears when listening to your voice is sharply reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        C

        (Echo)

        		 The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).

        D

        (Echo)

        		 The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).
        Settings (When Multiple Phenomena Occurred)
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
        A+C The other party hears background noise and weak echoes when listening to your voice. 1100

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).
        A+D The other party hears background noise and strong echoes when listening to your voice. 1200

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).
        B+C The other party hears a lot of background noise and weak echoes when listening to your voice. 2100

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).
        B+D The other party hears a lot of background noise and strong echoes when listening to your voice. 2200

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).

        Tech Tips


        • The default value is "0000".

        • Settings will be applied when the setting button is selected.

        • If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

        • If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.

  5. CHECK DAB RECEPTION (w/ DAB Function)

    Tech Tips


    • The reception condition of Digital Audio Broadcast (DAB) can be checked.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B002IJ7

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0001RW

      Select "Next Page" from the "Function Check/Setting I" screen.

    4. B002JX4

      Select "DAB Reception Check" from the "Function Check/Setting II" screen.

    5. B002HLGN01

      DAB Reception Check

      Screen Description
      Display Content
      *a: Up or down switch Enables the channel to be changed to the one to be checked.
      *b: Check/STOP switch

      • Check: Starts checking

      • STOP: Stops checking
      *c: Antenna connection check

        Displays DAB antenna connection status as follows:

      • OK: Connected properly

      • NG: Not connected properly

      • -: Not equipped with DAB antenna.
      *d: DAB tuner reception level check result description

        Displays DAB antenna reception levels as follows:

      • 111 or more: Font color is black (good reception).

      • 110 or less: Font color is red (poor reception).

      • -: Not equipped with DAB antenna.

      1. Select the "Check" button to start the DAB reception check.

      2. Check that the results are displayed when the DAB reception check is performed.

  6. CHECK GPS & VEHICLE SENSORS (w/ Navigation Antenna)

    Tech Tips


    • GPS information, vehicle signals and sensor signals are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B002KYF

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A000281

      Select "System Sensors Check" from the "Function Check/Setting I" screen.

    4. B002JB2N01

      System Sensors Check

      *a: GPS
      Display Content
      Reception number Displays reception condition of the satellites used to determine vehicle position Blue: P (In use) System is using GPS signal for location.
      Yellow: T (Receiving) System is tracking GPS signal for location.
      No color: Not in use System cannot receive GPS signal. (Searching for GPS signal)
      Status Displays reception status of the satellites used to determine vehicle position OK (H3D) High accuracy 3-dimensional location method is being used.
      OK (H2D) High accuracy 2-dimensional location method is being used.
      OK (3D) 3-dimensional location method is being used.
      OK (2D) 2-dimensional location method is being used.
      NG Location data cannot be used.
      error Reception error has occurred.
      - Any other state.
      Measurement ratio Displays the ratio of satellites performing measurements 3D The ratio of satellites performing 3D positioning, Hyper 3D positioning and Hyper 2D positioning is displayed.
      2D The ratio of satellites performing 2D positioning is displayed.
      NG The ratio of satellites not performing measurement is displayed.
      Date Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).
      Position Latitude and longitude information on current position is displayed.
      *b: SPD
      Display Content
      Pulse Count Displays the accumulated number of input pulses beginning when this screen is displayed
      Speed Displays vehicle speed
      *c: Sensor Signal
      Display Content Note
      Gyro Voltage Displays the output voltage of the gyro sensor -
      0 point Voltage Displays the zero-point voltage of the gyro sensor -
      Relative bearing Displays the output angle of the gyro sensor The amount of change in bearing angle (degrees) after the system sensor check screen is displayed (clockwise: "+", counterclockwise: "-").
      *d: Reset
      Display Content
      Reset When this switch is pressed and held for 3 seconds or more, the values for display items of SPD signal and gyro sensor signal are reset and displays "0".
      *e: Gyro/Distance Correction Study Situation
      Display Content
      Gyro/Distance correction study situation Displays learning status of Gyro/Distance correction

      1. When the "System Sensors Check" screen is displayed, check all the sensor signals.

        Tech Tips

        This screen is updated once per second.

    5. B002HUPN02

      GPS Time Setting

      Screen Description
      Display Content
      *a: Time display Displays the date and time in the device.
      *b: Time setting screen Setting is possible only when GPS signals are not being received.
      *c: Cursor movement switch Moves the cursor on the date and time setting screen to the right and left.
      *d: Adjustment switch Adjusts values of items selected by the cursor.
      *e: OK switch Selecting this switch after setting the date and time updates the date and time in the device (only when GPS signals are not received).

      1. When GPS signals are not being received, the data and time in the device can be adjusted.

        Tech Tips

        Time setting is possible only when GPS signals are not being received. When the navigation system is receiving GPS signals, priority is given to displaying the time and date received via GPS.

  7. CHECK SPEAKER

    Tech Tips


    • This function is used when checking the speaker wiring and whether the speakers are functioning properly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Turn audio mode on and play any audio source.

      Tech Tips

      This audio source will be used for the speaker check.

    2. Enter diagnostic mode.

      Click here

    3. B002HH2

      Select "Failure Diagnosis" from the "Service Menu" screen.

    4. A0001BO

      Select "System Check" from the "Failure Diagnosis" screen.

    5. B002JLG

      Select "SP Check ON" from the "System Check Mode" screen.

    6. Check the speaker wiring and check that the speakers are functioning properly.

      Tech Tips


      • Check that each speaker outputs sound from the selected audio source properly.

      • "SP Check OFF" is displayed during the speaker check.

      • Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

      • More than one speaker may sound simultaneously depending on the speaker wiring.

    7. Sound stops when any of the following conditions are met:


      1. The "SP Check OFF" switch is pressed.

      2. The power switch is turned off.

      3. Diagnostic mode is turned off.

      4. The screen is changed to another screen.

      5. Audio mode is turned off.

  8. CHECK SOFTWARE ERROR HISTORY

    Tech Tips

    This function is used to check the cause when the radio receiver assembly screen is blacked out.


    1. Check Software Error History.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Software Error History

      5. When an item is stored for Software Error History, record it before repairing the radio receiver assembly.

        Software Error History Screen Description
        Error Description Trigger Detail
        Software Reset Navi Microcomputer Hexadecimal Number
        Audio Microcomputer
        CAN Microcomputer
        No Video Signal Front Monitor
        Rear Monitor
        MOST Cold Restart Always

        Tech Tips


        • Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

    2. Clear Software Error History.


      1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  9. CHECK OPTICAL DISC ERROR HISTORY

    Tech Tips

    This function is used to check the cause of an optical disc error.


    1. Check Optical Disc Error History.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Optical Disc Error History

      5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

        Optical Disc Error History Screen Description
        Display Content
        Error Type Displays the type of error.
        Device Displays the malfunctioning device.
        Date Displays the date and time that the malfunction occurred.
        "Error Type" Screen Description
        Error Type Detection Condition Action
        Read Error When a disc read error occurs.

        Proceed to next suspected area shown in Problem Symptoms Table.

        Click here

        Disc damaged/upside down/dirty

        When it is determined that any of the following is the cause of the disc read error:


        • The disc cannot be read.

        • The disc cannot be read because of dirt or scratches.

        • The disc cannot be read because it is inserted upside down.
        Cannot determine disc type An unsuitable disc is inserted.
        DPS error When an error occurs while decoding MP3/WMA/AAC files.
        Some files are corrupt

        • When MP3/WMA/AAC files cannot be played back because they are unsupported.

        • Even though the file extensions are MP3, WMA or AAC, files cannot be played back because the header information cannot be read.
        Some files cannot be found

        • When a disc without music data is played back.

        • When there are no playable MP3/WMA/AAC files.
        Copy protection violation When a file with copyright protection that cannot be played back is played back.
        "Device" Screen Description
        Device Component
        DVD-P Radio receiver assembly*1
        CD-P Radio receiver assembly*2
        R-Seat DVD-P Not available

        • *1: w/ DVD Player

        • *2: w/ CD or VCD Player

        Tech Tips


        • Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

    2. Clear Optical Disc Error History.


      1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  10. Tech Tips


    • This function is used to detect disconnection of the video devices.

    • In order to inspect the RSE, a disc should be inserted into the radio receiver assembly.

    CHECK VIDEO DEVICE CONNECTION CHECK


    1. Check Video Device Connection Check.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.


        Body Electrical > Navigation System > Utility
        Tester Display
        Video Device Connection Check

      5. When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

        Tech Tips


        • DTCs are stored when errors are detected.

        • Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.

        Video Device Connection Check Screen Description
        Error Detected Image Line (Type) Areas to be Checked
        H/U - > Separate Display (GVIF) Digital video signal between the radio receiver assembly and multi-display assembly
        H/U - > Full RSE (GVIF) Not available
        RSE - > Seat Back Display RH (GVIF) Not available
        RSE - > Seat Back Display LH (GVIF) Not available
        Rear Camera - > H/U (NTSC) NTSC video signal between the radio receiver assembly and rear television camera assembly
        IPA/BGM/PVM ECU - > Separate Display (GVIF) Not available
        IPA/BGM/PVM ECU - > H/U (NTSC) Not available
        IPA/BGM/PVM ECU - > H/U (GVIF) Not available

    2. Clear Video Device Connection Check.


      1. When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  11. Tech Tips

    This function is used to check the connection history when the connection between the radio receiver assembly and a "Bluetooth" device is unstable.

    CHECK "Bluetooth" CONNECTION HISTORY


    1. Check "Bluetooth" Connection History.

      Tech Tips


      • "Bluetooth" Connection History displays data stored in the internal memory of the ECU, such as the date a "Bluetooth" connection was attempted and the progress of a "Bluetooth" connection.

      • By checking "Bluetooth" Connection History, the date, cause, etc. of a "Bluetooth" device failing to register or connect can be analyzed.

      • "Bluetooth" connection history indicates the estimated cause of a malfunction, but does not determine it. Therefore, checking "Bluetooth" Connection History may not improve the problem.

      • Performing inspection using the GTS before recording the "Bluetooth" Connection History may clear the operation history.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Bluetooth Connection History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Bluetooth Connection History

      5. When an item is stored for "Bluetooth" Connection History, record it before proceeding with troubleshooting.

        "Bluetooth" Connection History Screen Description
        Item Content
        Occurrence Start Date/Time Date and time of "Bluetooth" connection are displayed.
        Occurrence End Date/Time Date and time of "Bluetooth" disconnection are displayed.
        History Type Type of "Bluetooth" Connection History is displayed.
        Result "Bluetooth" connection result is displayed.
        Contents "Bluetooth" connection status is displayed.
        "Bluetooth" Address "Bluetooth" device address is displayed.
        Continuance Time The number of retries when "Bluetooth" connection was performed is displayed.
        History Type: ACC ON
        Result Contents Detail Areas to be Checked
        - - Power switch on (ACC) -
        History Type: Registration
        Result Contents Detail Areas to be Checked
        Success (HFP) No Error "Bluetooth" device was registered as a hands-free device properly. -
        Success (AVP) No Error "Bluetooth" device was registered as a "Bluetooth" audio device properly. -
        Failure Time Out Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.
        Authentication Error Wrong PIN code was input for PIN code verification. Perform "Bluetooth" device registration again. (Input PIN code correctly.)
        Did not select the confirmation button even though a passkey was displayed. Perform "Bluetooth" device registration again. (When a passkey is displayed, select the confirmation button.)
        A verification error occurred between the radio receiver assembly and "Bluetooth" device. Restart the radio receiver assembly and "Bluetooth" device, and operate them again.
        ACL Link Disconnection "Bluetooth" connection was disconnected by operating the "Bluetooth" device. Perform "Bluetooth" device registration again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" device registration again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio receiver assembly and perform "Bluetooth" device registration again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" device registration again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" device registration again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        Memory Write Failure "Bluetooth" device information could not be stored in the radio receiver assembly. Perform "Bluetooth" device registration again.
        Other Error An error other than above occurred. After turning the power switch off and back on (IG) again, perform "Bluetooth" device registration again.
        Cancel No Error Registration was suspended by operating the radio receiver assembly or "Bluetooth" device. -
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Success (HFP)

        • Manual Connect Success (HFP)

        		 No Error "Bluetooth" device was connected as a hands-free device properly. -

        • Auto Connect Failure (HFP)

        • Manual Connect Failure (HFP)

        		 Time Out Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.
        Authentication Error Verification of authentication key between the radio receiver assembly and "Bluetooth" device failed. If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again.
        A verification error occurred between the radio receiver assembly and "Bluetooth" device. Restart the radio receiver assembly and "Bluetooth" device, and operate them again.
        Page Time Out Could not find a "Bluetooth" device near the radio receiver assembly. Bring the "Bluetooth" device near the radio receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Failure (HFP)

        • Manual Connect Failure (HFP)

        		 ACL Link Disconnection "Bluetooth" connection was disconnected by operating the "Bluetooth" device. Perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        SDP Error HFP was disabled on the "Bluetooth" device. Enable HFP on the "Bluetooth" device and perform "Bluetooth" connection again.
        "Bluetooth" device which operation had not been confirmed was used.

        Check that the "Bluetooth" device is hands-free compatible and its operation has been confirmed.

        Click here

        Other Error An error other than above occurred. After turning the power switch off and back on (IG) again, perform "Bluetooth" device registration again.
        Manual Connect Cancel (HFP) No Error Connection was interrupted by operating the radio receiver assembly or "Bluetooth" device. -
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Success (AVP)

        • Manual Connect Success (AVP)

        		 No Error "Bluetooth" device was connected as a "Bluetooth" audio device properly. -

        • Auto Connect Failure (AVP)

        • Manual Connect Failure (AVP)

        		 Time Out Could not perform "Bluetooth" connection properly.

        • Check that the "Bluetooth" device is in the cabin.

        • Check that the "Bluetooth" device is not connected to another device using the "Bluetooth" connection.

        • Restart the "Bluetooth" device and operate it again.
        Authentication Error Verification of authentication key between the radio receiver assembly and "Bluetooth" device failed. If "Bluetooth" connection failed again even though the "Bluetooth" connection was performed, perform registration again.
        A verification error occurred between the radio receiver assembly and "Bluetooth" device. Restart the radio receiver assembly and "Bluetooth" device, and operate them again.
        Page Time Out Could not find a "Bluetooth" device near the radio receiver assembly. Bring the "Bluetooth" device near the radio receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        History Type: Connection
        Result Contents Detail Areas to be Checked

        • Auto Connect Failure (AVP)

        • Manual Connect Failure (AVP)

        		 ACL Link Disconnection "Bluetooth" connection was disconnected by operating the "Bluetooth" device. Perform "Bluetooth" connection again.
        "Bluetooth" connection could not be established due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        "Bluetooth" device was outside the communication area. Bring the "Bluetooth" device near the radio receiver assembly and perform "Bluetooth" connection again.
        "Bluetooth" setting on the "Bluetooth" device was off. Change the "Bluetooth" setting to on and perform "Bluetooth" connection again.
        "Bluetooth" device was off. Turn the "Bluetooth" device on and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        SDP Error AVP was disabled on the "Bluetooth" device. Enable AVP on the "Bluetooth" device and perform "Bluetooth" connection again.
        "Bluetooth" device which operation had not been confirmed was used.

        Check that the "Bluetooth" device is "Bluetooth" audio compatible and its operation has been confirmed.

        Click here

        Other Error An error other than above occurred. After turning the power switch off and back on (IG) again, perform "Bluetooth" device registration again.
        Manual Connect Cancel (AVP) No Error Connection was interrupted by operating the radio receiver assembly or "Bluetooth" device. -
        History Type: Disconnection
        Result Contents Detail Areas to be Checked
        Disconnection Complete (HFP) Link Loss The "Bluetooth" device was moved outside of the communication area. Move the "Bluetooth" device into the communication area.
        "Bluetooth" connection was disconnected due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        Disconnection from Partner "Bluetooth" connection was disconnected by operating the "Bluetooth" device. -
        Disconnection from Self "Bluetooth" connection was disconnected by operating the radio receiver assembly. -
        Other Error An error other than above occurred. After turning the power switch off and back on (IG) again, perform "Bluetooth" device registration again.
        Disconnection Complete (AVP) Link Loss The "Bluetooth" device was moved outside of the communication area. Move the "Bluetooth" device into the communication area.
        "Bluetooth" connection was disconnected due to wave interference around the vehicle. Check for wave interference and perform "Bluetooth" connection again.
        A malfunction occurred in the "Bluetooth" device. Restart the "Bluetooth" device and operate it again.
        Disconnection from Partner "Bluetooth" connection was disconnected by operating the "Bluetooth" device. -
        Disconnection from Self "Bluetooth" connection was disconnected by operating the radio receiver assembly. -
        Other Error An error other than above occurred. After turning the power switch off and back on (IG) again, perform "Bluetooth" device registration again.
        History Type: Send
        Result Contents Detail Areas to be Checked
        Success No Error Call was made properly. -
        Failure Out of Service Outside the cellular phone service area. Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate the device again.
        Redial Regulation Redial of the "Bluetooth" device was restricted and could not make a hands-free call. Restart the "Bluetooth" device and operate it again.
        Other Error Could not make a hands-free call due to a "Bluetooth" device malfunction. Restart the "Bluetooth" device and operate it again.
        Could not make a hands-free call due to a radio receiver assembly malfunction. After turning the power switch off and back on (IG) again, perform "Bluetooth" device registration again.
        Could not make a hands-free call from the radio receiver assembly because the call status of the "Bluetooth" device was not transmitted to the radio receiver assembly. Restart the "Bluetooth" device and operate it again.

    2. Clear "Bluetooth" Connection History.


      1. When DTCs are cleared using any of the following operations, "Bluetooth" Connection History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  12. CHECK "Wi-Fi" CONNECTION HISTORY (w/ "Wi-Fi" Function)

    Tech Tips

    This function is used to check the connection history when the connection between the radio receiver assembly and a "Wi-Fi" device is unstable.


    1. Check "Wi-Fi" Connection History.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Wi-Fi Connection History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Wi-Fi Connection History

      5. When an item is stored for "Wi-Fi" Connection History, record it before proceeding with troubleshooting.

        "Wi-Fi" Connection History Screen Description
        Item Content
        Occurrence Date/Time Year is displayed in 4 digits and month, date, hour, minute and second are displayed in 2 digits
        Result Connect/Disconnect Success
        Timeout
        Communication Error
        Authentication Failure
        Disconnection Failure
        Other Failure
        Contents No Error
        AP Connection Error
        AP Connection Error (WPS)
        DHCP Connection Error
        DNS Connection Error
        HTTP Connection Error
        Other Error
        Destination MAC Address Displayed in lower case hexadecimal format with "-" inserted every two characters.
        Destination SSID Data is read as ASCII code Data is read as ASCII code
        WLAN Standard 802.11 b
        802.11 g
        802.11 n
        Undetectable
        Received Signal Strength -127 dBm to +127 dBm
        Data Rate 1.0 Mbps
        2.0 Mbps
        5.5 Mbps
        6.0 Mbps
        6.5 Mbps
        9.0 Mbps
        11.0 Mbps
        12.0 Mbps
        13.0 Mbps
        18.0 Mbps
        19.5 Mbps
        24.0 Mbps
        26.0 Mbps
        36.0 Mbps
        39.0 Mbps
        48.0 Mbps
        52.0 Mbps
        54.0 Mbps
        58.5 Mbps
        65.0 Mbps
        Undetectable
        Packet Error Rate Displayed in decimal format with "%"

        Tech Tips

        If there is nothing to display in the "Content" column, "-" or "No Information" is displayed.

  13. ENFORM RESET PROCEDURE (w/ Enform Function)


    1. Duplicate the problem symptom.

    2. Check cellular phone compatibility.


      1. Check if the cellular phone/vehicle is compatible (Refer to http://www.lexus.com.au/).

      2. If the cellular phone is not compatible, recommend to the customer a compatible cellular phone.

    3. Delete all paired devices from the cellular phone.


      1. This procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    4. Remove the Enform app from the phone.

      Note

      Only perform this step if the customer is present and approves.


      1. The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    5. Reset the phone.

      Note

      Only perform this step if the customer is present and approves.


      1. Turn off the phone and remove the battery for 15 seconds. For instructions on how to reset cellular devices, refer to the appropriate manufacturer's website.

    6. Reinstall the Enform app on the phone (if removed).


      1. This procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    7. Delete all personal data from the radio receiver assembly.


      1. Delete all personal data from the radio receiver assembly.

        Note

        Only perform this step if the customer is present and approves.

        Tech Tips

        Re-installation of applications must be completed before applications will appear on the radio receiver assembly.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Note

      After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

      Click here


      1. Record all radio station presets.

      2. Disconnect the cable from the negative (-) auxiliary battery terminal and leave it disconnected for 2 minutes.

    9. Check if the problem symptom has been repaired.