DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:C1A40

DTC Code DTC Name
C1A40 ENG / EHV Device

DESCRIPTION

When the driving support ECU assembly receives a hybrid control system or SFI system malfunction signal from the hybrid vehicle control ECU, this DTC is stored.

When DTC C1A40 is stored, the hybrid control system or SFI system DTC will also be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A40 ENG / EHV Device While the power switch is on (IG), a hybrid control system or SFI system malfunction signal is detected for 3 seconds or more.

  • Hybrid control system

  • SFI system

  • Hybrid vehicle control ECU

  • ECM

  • Driving support ECU assembly

CAUTION / NOTICE / HINT

Note

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

PROCEDURE


  1. CHECK FOR DTC (HYBRID CONTROL SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    5. Check for DTCs.

      Click here


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      Hybrid control system DTCs are not output A
      Hybrid control system DTCs are output B

    B

    GO TO HYBRID CONTROL SYSTEM Click here

    A

  2. CHECK FOR DTC (SFI SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Check for DTCs.

      for w/ EGR System:

      Click here

      for w/o EGR System:

      Click here


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      SFI system DTCs are not output A
      SFI system DTCs are output B

    B

    GO TO SFI SYSTEM Click here

    A

  3. REPLACE DRIVING SUPPORT ECU ASSEMBLY


    1. Replace the driving support ECU assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Powertrain > Radar Cruise > Clear DTCs

    2. Make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the system cannot detect the malfunction.

    3. Check for DTCs.

      Click here


      Powertrain > Radar Cruise > Trouble Codes
      Result
      Result Proceed to
      DTC C1A40 is output A
      DTC C1A40 is not output B

    B

    END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

    A

  5. REPLACE HYBRID VEHICLE CONTROL ECU


    1. Replace the hybrid vehicle control ECU with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Powertrain > Radar Cruise > Clear DTCs

    2. Make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the system cannot detect the malfunction.

    3. Check for DTCs.

      Click here


      Powertrain > Radar Cruise > Trouble Codes
      Result
      Result Proceed to
      DTC C1A40 is not output A
      DTC C1A40 is output B

    A

    END (HYBRID VEHICLE CONTROL ECU WAS DEFECTIVE)

    B

    REPLACE ECM Click here