OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or waterless hand cleaner thoroughly to remove any used engine oil. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. A01CQB0

      Remove the 4 screws and service hole cover.

    3. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    4. Clean and install a new gasket and the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

    5. Install the service hole cover with the 4 screws.

  2. REMOVE OIL FILTER CAP ASSEMBLY


    1. A01CPKLC02
      *a Pipe
      *b Hose

      Connect a hose with an inner diameter of 15 mm (0.591 in.) to the pipe.

    2. A01CMVV

      Remove the oil filter drain plug from the oil filter cap assembly.

      Note

      Do not remove the O-ring (for drain plug).

    3. A01CQCTC01
      *1 Oil Filter Cap Assembly
      *2 O-Ring (for drain plug)
      *a Valve
      *b Pipe

      Install the pipe to which the hose was attached to the oil filter cap assembly.

      Note

      Insert the pipe with the O-ring (for drain plug) attached to the oil filter cap assembly side.

      Tech Tips

      Use a container to catch the draining engine oil.

    4. A01CMY9

      Check that the engine oil has been drained and remove the pipe and O-ring (for drain plug).

      Tech Tips

      Remove the pipe in the direction indicated by the arrow shown in the illustration.

    5. A01CRQLC04
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap assembly.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. A01CQC1C01
      *1 Oil Filter Element
      *2 O-Ring (for cap)

      Remove the oil filter element and O-ring (for cap) from the oil filter cap assembly.

      Note

      To prevent damage to the O-ring groove, remove the O-ring (for cap) by hand and do not use any tools.

  3. INSTALL OIL FILTER CAP ASSEMBLY


    1. Clean the inside of the oil filter cap assembly, the threads and O-ring groove.

    2. A01CR88C01
      *1 O-Ring (for cap)
      *a CORRECT
      *b INCORRECT

      Apply a light coat of engine oil to the new O-ring (for cap), and install it to the oil filter cap assembly.

      Note


      • Be sure to install the O-ring in the proper position, otherwise engine oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element to the oil filter cap assembly.

    4. Remove any dirt or foreign matter from the installation surface and inside of the engine.

    5. Again apply a light coat of engine oil to the O-ring (for cap), and install the oil filter cap assembly.

      Note

      Make sure that the O-ring (for cap) is not pinched.

    6. A01CNN2C01
      *1 Oil Filter Cap Assembly
      *2 O-Ring (for cap)
      *3 Stiffening Crankcase Assembly
      *a No Gap

      Using SST, tighten the oil filter cap assembly.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the oil filter cap assembly, check for gaps between the installation surfaces and protrusion of O-ring (for cap).

    7. Apply a light coat of engine oil to a new O-ring (for drain plug), and install it to the oil filter cap assembly.

      Note

      Remove any dirt or foreign matter from the installation surface.

    8. A01CPGVC01
      *1 O-Ring (for drain plug)

      Install the oil filter drain plug to the oil filter cap assembly.

      Torque:
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Make sure that the O-ring (for drain plug) is not pinched.

  4. ADD ENGINE OIL


    1. Add new engine oil and install the oil filler cap.

      Standard Oil Grade
      Oil Grade Oil Viscosity
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter change 4.0 liters (4.2 US qts, 3.5 Imp. qts)
      Drain and refill with oil filter change 4.4 liters (4.6 US qts, 3.9 Imp. qts)
      Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)

  5. INSPECT ENGINE OIL LEVEL

    Click here

  6. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.