HYBRID CONTROL SYSTEM, Diagnostic DTC:P0E32-585

DTC Code DTC Name
P0E32-585 DC/DC Converter Voltage Sensor "A" Range / Performance

DTC SUMMARY


  1. MALFUNCTION DESCRIPTION

    The hybrid vehicle control ECU detects a VL sensor malfunction.

    The cause of this malfunction may be one of the following:


      Inside of inverter voltage sensor circuit malfunction

    • Voltage sensor malfunction

    • Motor generator control ECU (MG ECU) malfunction

    • Communication (wire harness) malfunction


      High voltage system malfunction

    • Inverter with converter assembly malfunction

DESCRIPTION

Refer to the description for DTC P0E33-589.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0E32-585 DC/DC Converter Voltage Sensor "A" Range / Performance

Boost converter voltage (VL) sensor performance malfunction:

When not boosting, differences between "VL-Voltage before Boosting" and "Power Resource VB", and "VL-Voltage before Boosting" and "VH-Voltage after Boosting" are large.

(1 trip detection logic)

 Inverter with converter assembly Comes on

Master Warning Light:

Comes on
Related Data List
DTC No. Data List
P0E32-585

  • VL-Voltage before Boosting

  • Power Resource VB

  • VH-Voltage after Boosting

  • Boost Ratio

CAUTION / NOTICE / HINT

Tech Tips

When the accelerator pedal is not depressed with the power switch on (READY) and the shift lever in P, if "VH-Voltage after Boosting" and the "Power Resource VB" is approximately same after repair, the condition is judged as normal.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      P0E32-585 only is output, or DTCs except the ones in the tables below are also output. A
      DTCs shown in Table 1 are output simultaneously. B
      DTCs shown in Table 2 are output simultaneously. C
      Table 1
      Malfunction Content Relevant DTC
      Microcomputer malfunction P0A1A-151, 658 Generator Control Module
      P0A1B-786 Drive Motor "A" Control Module
      P0A1D-148 Hybrid Powertrain Control Module
      P1C2A-155 Generator A/D Converter Circuit
      P1CA6-156 Generator Control Module Malfunction
      P1CA7-193 Drive Motor Control Module Malfunction
      P2511-149 HV CPU Power Relay Sense Circuit Intermittent No Continuity
      P3133-659 Communication Error from Generator to Drive Motor "A"
      P3134-661 Communication Error from Drive Motor "A" to Generator
      P324E-788 MG-ECU Power Relay Intermittent Circuit
      Power source circuit malfunction P06E6-164 Sensor Power Supply "C" Circuit / Open
      P1C73-512 Sensor Standard Voltage "F" Circuit / Open
      Communication system malfunction U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"
      System malfunction P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
      P0D30-267 Drive Motor "A" Inverter Voltage Sensor Circuit High
      P0E33-589 DC/DC Converter Voltage Sensor "A" Low
      P0E34-590 DC/DC Converter Voltage Sensor "A" High
      Malfunction Content Relevant DTC
      Microcomputer malfunction P0AFC-123 Hybrid Battery Pack Sensor Module
      Sensor and actuator circuit malfunction P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
      P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
      P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
      P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
      P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
      P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
      P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
      P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
      P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
      P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
      P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
      P0B74-123 Hybrid Battery Voltage Sensor "L" Circuit Low
      P0B79-123 Hybrid Battery Voltage Sensor "M" Circuit Low
      P0B7E-123 Hybrid Battery Voltage Sensor "N" Circuit Low
      P0B83-123 Hybrid Battery Voltage Sensor "O" Circuit Low
      P0B88-123 Hybrid Battery Voltage Sensor "P" Circuit Low
      P0B8D-123 Hybrid Battery Voltage Sensor "Q" Circuit Low
      P0B92-123 Hybrid Battery Voltage Sensor "R" Circuit Low
      P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

      Tech Tips


      • *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

      • P0E32-585 may be output as a result of the malfunction indicated by the DTCs above.


        1. The chart above is listed in inspection order of priority.

        2. Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)

    5. Turn the power switch off.


    A

    REPLACE INVERTER WITH CONVERTER ASSEMBLY Click here

    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    C

    GO TO DTC CHART (HYBRID BATTERY SYSTEM) Click here