HYBRID CONTROL SYSTEM, Diagnostic DTC:P3004-803

DTC Code DTC Name
P3004-803 High Voltage Power Resource

DTC SUMMARY


  1. MALFUNCTION DESCRIPTION

    The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects an open circuit malfunction.

    Tech Tips


    • This DTC is differentiated from P3004-131 based on detection timing (after power switch is turned on (READY)). If P3004-131 is also output at the same time, first perform troubleshooting for P3004-131.

    • If there is a SMRG stuck open malfunction, only P3004-803 is output.

    The cause of this malfunction may be one of the following:


      Inside of inverter voltage sensor (VH or VL) circuit malfunction

    • Voltage sensor (VH or VL) malfunction

    • Motor generator control ECU (MG ECU) malfunction

    • Communication (wire harness) malfunction


      High voltage system malfunction

    • HV battery malfunction

    • Hybrid battery junction block assembly malfunction

    • Inverter with converter assembly malfunction

    • High-voltage wire harness malfunction

    • High-voltage connector or connection malfunction


      Low-voltage circuit (12 V) malfunction

    • Hybrid vehicle control ECU malfunction

    • Hybrid battery junction block assembly malfunction

    • Low voltage wire harness malfunction

    • Low voltage connector malfunction

DESCRIPTION

Refer to the description for DTC P0AE6-225.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3004-803 High Voltage Power Resource

High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.

When the power switch is on (READY), both "VL-Voltage before Boosting" and "VH-Voltage after Boosting" drop abnormally.

The EV electric battery fuse is blown, the service plug grip is removed, SMRB or SMRG remains open, or the high-voltage cable has an open circuit.

(1 trip detection logic)

  • Hybrid battery junction block assembly

  • Wire harness or connector

 Does not come on

Master Warning Light:

Comes on
Related Data List
DTC No. Data List
P3004-803

  • VL-Voltage before Boosting

  • VH-Voltage after Boosting

  • Power Resource VB

The following items can be helpful when performing repairs:


WIRING DIAGRAM

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click here

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the power switch on (READY) and wait for 30 seconds or more.

    If the DTC is not output again, drive the vehicle according to the freeze frame data item "Vehicle Spd" for approximately 5 minutes.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      P3004-803 only is output, or DTCs except the ones in the table below are also output. A
      Any of the following DTCs including pending DTCs are also output. B
      P0A95-123 is also output. C
      Malfunction Content Relevant DTC
      Microcomputer malfunction P0A1A-151, 155, 156, 658, 659 Generator Control Module
      P0A1B-164, 193, 512, 661, 786 Drive Motor "A" Control Module
      P0A1D-148 Hybrid Powertrain Control Module
      P324E-788 MG-ECU Power Relay Intermittent Circuit
      Power source circuit malfunction P2511-149 ECM/PCM Power Relay Sensor Circuit Intermittent
      Communication system malfunction U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"
      Sensor and actuator circuit malfunction P0A78-266, 267, 586 Drive Motor "A" Inverter Performance
      P0A94-442 DC / DC Converter Performance
      P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
      P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
      P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
      P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
      P0C76-523 Hybrid Battery System Discharge Time Too Long
      System malfunction P3004-131, 132 High Voltage Power Resource

      Tech Tips


      • *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

      • P3004-803 may be output as a result of the malfunction indicated by the DTCs above.


        1. The chart above is listed in inspection order of priority.

        2. Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    C

    GO TO DTC CHART (P0A95-123) Click here

    A

  2. CLEAR DTC

    Result
    Proceed to
    NEXT

    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read and record the DTCs and freeze frame data.


      Powertrain > Hybrid Control > Trouble Codes

    5. Clear the DTCs and freeze frame data.


      Powertrain > Hybrid Control > Clear DTCs

    6. Turn the power switch off.

      Result
      Proceed to
      NEXT

    NEXT

  3. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. With the vehicle stopped, apply the parking brake and turn the power switch on (READY).

      Tech Tips


      • If the power switch could not be turned on (READY), turn the power switch off and check for DTCs after turning the power switch on (READY) again.

      • Because P3004-131 uses 2 trip detection logic, the DTC detection conditions need to be met 2 times.

    3. Ensure the safety of the areas in front and at the back of the vehicle.

    4. Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.

      Tech Tips


      • Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.

      • Depressing both the accelerator pedal and brake pedal at the same time causes "Accelerator and Brake Depress" in the inappropriate operation and history data to be counted.

    5. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    6. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      P3004-803 is output, or no DTCs are output. A
      Power switch could not be turned on (READY) and DTC P3004-131 is output. B

    7. Turn the power switch off.


    B

    GO TO DTC CHART (P3004-131) Click here

    A

  4. CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

    Result
    Proceed to
    OK
    NG

    1. A01CQIMC01
      *A for LHD
      *B for RHD

      Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors.

      Click here

      OK
      The connectors are connected securely and there are no contact pressure problems.
      Result
      Proceed to
      OK
      NG

    NG

    CONNECT SECURELY

    OK

  5. CHECK CONNECTOR CONNECTION CONDITION (NO. 2 HYBRID BATTERY PACK WIRE CONNECTOR)

    Result
    Result Proceed to
    OK A
    NG (The connector is not connected securely.) B
    NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. B002IRF

      Check the connection condition of the No. 2 hybrid battery pack wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

      Click here

      OK
      - The connector is connected securely.
      - The terminals are not deformed and are connected securely.
      - No water or foreign matter in the connector.
      Result
      Result Proceed to
      OK A
      NG (The connector is not connected securely.) B
      NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

    B

    CONNECT SECURELY

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  6. CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the No. 2 hybrid vehicle battery shield reinforcement.

      Click here

    3. B002IJY

      Check the connector connections and contact pressure of the relevant terminals for the hybrid battery junction block assembly connector.

      Click here

      OK
      The connectors are connected securely and there are no contact pressure problems.

    4. Install the No. 2 hybrid vehicle battery shield reinforcement.

      Result
      Proceed to
      OK
      NG

    NG

    CONNECT SECURELY

    OK

  7. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Disconnect the I115 hybrid vehicle control ECU connector.

    3. Remove the No. 2 hybrid vehicle battery shield reinforcement.

      Click here

    4. B002K92C97
      *a

      Rear view of wire harness connector

      (to Hybrid Vehicle Control ECU)
      *b

      Rear view of wire harness connector

      (to Hybrid Battery Junction Block Assembly)

      Disconnect the y1 hybrid battery junction block assembly connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I115-4 (SMRB) - y1-4 (SMRB) Power switch off Below 1 Ω
      I115-1 (SMRG) - y1-1 (SMRG) Power switch off Below 1 Ω

    6. Reconnect the y1 hybrid battery junction block assembly connector.

    7. Install the No. 2 hybrid vehicle battery shield reinforcement.

    8. Reconnect the I115 hybrid vehicle control ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR