HYBRID CONTROL SYSTEM, Diagnostic DTC:P0AEE-277, P0AF1-276

DTC Code DTC Name
P0AEE-277 Motor Inverter Temperature Sensor "A" Circuit Range / Performance
P0AF1-276 Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic

DTC SUMMARY


  1. MALFUNCTION DESCRIPTION

    These DTCs indicate the temperature sensor value for motor inverter is abnormal. The cause of this malfunction may be one of the following:


      Internal inverter malfunction

    • Inverter with converter assembly internal circuit malfunction


      Hybrid cooling system malfunction

    • Coolant circulation abnormal (frozen or leaking, etc.)


      Inverter low-voltage circuit malfunction

    • The connectors are not connected properly

DESCRIPTION

The MG ECU, which is built into in the inverter with converter assembly, detects the temperature of the motor inverter using the temperature sensor built into the motor inverter. If necessary, the MG ECU will limit inverter output to help prevent motor inverter overheating. The hybrid vehicle control ECU also detects malfunctions in the sensor based on the temperature sensor values. The inverter with converter assembly detects malfunctions in the motor inverter temperature sensor and its wiring.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AEE-277 Motor Inverter Temperature Sensor "A" Circuit Range / Performance

Motor inverter temperature calculated by the hybrid vehicle control ECU is different from the actual temperature for 10 seconds or more, and the motor inverter temperature is excessively high.

(1 trip detection logic)

  • Inverter cooling system

  • Cooling fan system

  • Inverter with converter assembly

  • Wire harness or connector

 Does not come on

Master Warning Light:

Comes on
P0AF1-276 Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic

Sudden change in motor inverter temperature sensor output or hunting:

Motor inverter temperature is high and either of the following conditions is met:


  1. Unusual sudden change in motor inverter temperature sensor output occurs and the offset continues for a certain period of time.*

  2. Unusual sudden change in motor inverter temperature sensor output occurs repeatedly.*

(1 trip detection logic)

  • Inverter cooling system

  • Cooling fan system

  • Inverter with converter assembly

  • Wire harness or connector

 Does not come on

Master Warning Light:

Comes on

Tech Tips

*: If only DTC P0AF1-276 is output, a temperature sensor malfunction is more likely to be the cause than a sudden change in actual temperature.

Related Data List
DTC No. ECU Data List
P0AEE-277

  • Inverter Temp- (MG2)

  • Inverter Temp- (MG1)
P0AF1-276

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the power switch on (READY) and wait for 90 seconds or more.

  2. Drive the vehicle for approximately 10 minutes referring to the following freeze frame data or Data List items: "Vehicle Spd".

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      P0AEE-277 or P0AF1-276 only is output, or DTCs except the ones in the table below are also output. A
      Any of the following DTCs are also output. B
      Relevant DTC
      P0A93-346 Inverter Cooling System Performance
      P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
      P314A-828 Inverter Coolant Pump Speed Signal

      Tech Tips

      P0AEE-277 or P0AF1-276 may be output as a result of the malfunction indicated by the DTCs above.

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  2. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

    Result
    Result Proceed to
    OK A
    NG (The connector is not connected securely.) B
    NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. B002I4J

      Check the connection condition of the low voltage connector of the inverter with converter assembly and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

      Click here

      Note

      Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

      OK
      - The connector is connected securely.
      - The terminals are not deformed and are connected securely.
      - No water or foreign matter in the connector.
      Result
      Result Proceed to
      OK A
      NG (The connector is not connected securely.) B
      NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

      Tech Tips

      When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.


    B

    CONNECT SECURELY

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  3. CHECK COOLING SYSTEM

    Click here

    Tech Tips

    If the "Cooling System" inspection results are normal, perform the next step.

    Result
    Proceed to
    NEXT

    NEXT

    REPLACE INVERTER WITH CONVERTER ASSEMBLY Click here