SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P0106

DTC Code DTC Name
P0106 Manifold Absolute Pressure Circuit Problem

DESCRIPTION

B002I43E01

The manifold absolute pressure sensor detects pressure inside the intake manifold as an absolute pressure with a built-in sensor and outputs it as voltage. Based on the voltage from the manifold absolute pressure sensor, the ECM controls the purge VSV and corrects any errors in the air fuel ratio due to change in pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0106 Manifold Absolute Pressure Circuit Problem Intake manifold pressure measured after engine start drops by less than 2 kPa(abs) [15 mmHg(abs)] compared to the intake manifold pressure (atmospheric pressure) measured before engine start (2 trip detection logic).

  • Intake system

  • Manifold absolute pressure sensor

 Comes on DTC stored

MONITOR DESCRIPTION

When the intake manifold pressure measured after engine start drops by less than 2 kPa(abs) [15 mmHg(abs)] compared to the intake manifold pressure (atmospheric pressure) measured before engine start, the ECM interprets this as a malfunction in the manifold absolute pressure sensor and stores DTC P0106.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the power switch off and wait for at least 30 seconds.

  5. Turn the power switch on (IG) and turn the GTS on.

  6. Put the engine in inspection mode (maintenance mode).

    Click here

  7. Start the engine and warm it up until the engine coolant temperature reaches 73°C (163°F) or higher.

  8. Move the shift lever to N.

  9. Idle the engine for 10 seconds or more [A].

  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

  11. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  13. Input the DTC: P0106.

  14. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0106)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTC P0106 is output A
      DTC P0106 and other DTCs are output B

      Tech Tips

      If any DTCs other than P0106 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. READ VALUE USING GTS (MAP)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAP.


      Powertrain > Engine and ECT > Data List
      Tester Display
      MAP

    5. Read the MAP value.

    6. Put the engine in inspection mode (maintenance mode).

      Click here

    7. Start the engine.

    8. Read the MAP value at idling.

      Standard
      Engine Condition GTS Display
      Power switch on (IG) 80 to 110 kPa(abs) [600 to 825 mmHg(abs)]
      Idling 20 to 40 kPa(abs) [150 to 300 mmHg(abs)]
      Result
      Proceed to
      OK
      NG

    OK

    CHECK FOR INTERMITTENT PROBLEMS Click here

    NG

  3. CHECK INTAKE SYSTEM


    1. Check the intake system for vacuum leaks.

      Click here

      OK
      No leaks in intake system.

      Tech Tips

      Perform "Inspection After Repair" after repairing or replacing the intake system.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR Click here

    NG

    REPAIR OR REPLACE INTAKE SYSTEM