FUEL TANK(w/ Canister Pump Module) REMOVAL

PROCEDURE


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  2. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT FLOOR COVER CENTER LH

    B002I11

    1. Remove the bolt, 2 nuts and 6 clips from the front floor cover center LH.

    2. B002HC6

      Loosen the nut and remove the front floor cover center LH.

  5. REMOVE NO. 1 FLOOR UNDER COVER


    1. B002J73

      Detach the clip and remove the 2 nuts and No. 1 floor under cover.

  6. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. B002L1J

      Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

      Click here

  7. DISCONNECT FUEL TANK TO CANISTER TUBE SUB-ASSEMBLY


    1. B002H1XC01
      *a Up

      Disconnect the fuel tank to canister tube sub-assembly.


      1. Pinch the retainer and then raise it, and disconnect the fuel tank to canister tube sub-assembly.

        Note


        • Do not use any tools in this procedure.

        • Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary.

          Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.

  8. REMOVE FUEL HOSE PROTECTOR


    1. B002IC6

      Detach the claw and remove the fuel hose protector from the fuel tank assembly and fuel tank to filler pipe hose.

  9. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    1. B002I9A

      Loosen the hose clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.

  10. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


    1. B002JSJ

      Disconnect the clamp and disconnect the fuel tank vent hose sub-assembly from the No. 2 fuel tank band.

  11. REMOVE FUEL TANK ASSEMBLY


    1. B002IOI

      Disconnect the 4 wire harness clamps from the 3 No. 4 fuel tube clamps and the bracket on the vehicle side.

    2. Using an engine lifter and attachments, support the fuel tank assembly.

    3. B002HJ5

      Remove the 2 bolts and No. 1 fuel tank band.

    4. Remove the 2 bolts and No. 2 fuel tank band.

    5. Slightly lower the engine lifter.

      Note

      Be careful not to cut the wiring.

    6. B002HC4

      Disconnect the fuel tank breather tube sub-assembly from the fuel tank assembly.

      Click here

    7. B002IW1

      Disconnect the fuel pump connector and fuel sender gauge assembly connector.

      Note


      • Before starting the operation, check that there is no mud or other dirt on the connector.

      • Do not use any tools.

    8. Disconnect the 2 wire harness clamps from the 3 No. 4 fuel tube clamps.

  12. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

    Click here

  13. REMOVE FUEL TANK VENT TUBE SET PLATE

    Click here

  14. REMOVE FUEL SUCTION TUBE ASSEMBLY

    Click here

  15. REMOVE FUEL SENDER GAUGE ASSEMBLY

    Click here

  16. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. B002JVV

      Disconnect the 5 clamps and remove the fuel tank main tube sub-assembly from the 5 No. 4 fuel tube clamps.

  17. REMOVE NO. 4 FUEL TUBE CLAMP


    1. B002KKY

      Remove the 5 No. 4 fuel tube clamps from the fuel tank assembly.