ENGINE UNIT REMOVAL

PROCEDURE


  1. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    1. A01CQR0

      Remove the engine oil level dipstick.

    2. Remove the bolt and engine oil level dipstick guide.

    3. Remove the O-ring from the engine oil level dipstick guide.

  2. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    1. A01CP31

      Remove the bolt and V-ribbed belt tensioner assembly.

  3. REMOVE COMPRESSOR ASSEMBLY WITH MOTOR

    Click here

  4. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET


    1. A01CP6Q

      Remove the 4 bolts and No. 1 compressor mounting bracket.

  5. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

  6. REMOVE NO. 2 EGR PIPE (w/ EGR System)

    Click here

  7. REMOVE NO. 2 MANIFOLD STAY

    Click here

  8. REMOVE MANIFOLD STAY

    Click here

  9. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

    Click here

  10. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

    Click here

  11. REMOVE WATER BY-PASS PIPE (w/ EGR System)


    1. A01CPRH

      Remove the 4 bolts, water by-pass pipe and 2 gaskets.

  12. REMOVE EGR COOLER ASSEMBLY (w/ EGR System)


    1. A01CNZQ

      Slide the hose clamp and disconnect the No. 5 water by-pass hose from the EGR cooler assembly.

    2. A01COYT

      Remove the bolt and nut, and disconnect the No. 1 EGR pipe from the EGR cooler assembly.

    3. A01CPT3

      Remove the bolt, nut and EGR cooler assembly.

    4. Remove the gasket from the No. 1 EGR pipe.

  13. REMOVE NO. 5 WATER BY-PASS HOSE (w/o EGR System)


    1. A01CRDL

      Slide the 2 hose clamps and remove the No. 5 water by-pass hose from the water by-pass pipe and No. 3 water by-pass pipe.

  14. REMOVE NO. 1 WATER BY-PASS PIPE (w/o EGR System)


    1. A01H68I

      Remove the 3 bolts, No. 1 water by-pass pipe and gasket.

  15. REMOVE EGR VALVE ASSEMBLY (w/ EGR System)

    Click here

  16. REMOVE NO. 3 WATER BY-PASS HOSE


    1. A01CPK2

      Slide the hose clamp and remove the No. 3 water by-pass hose.

  17. REMOVE NO. 1 WATER BY-PASS HOSE (w/ EGR System)


    1. A01CP3F

      Slide the hose clamp and remove the No. 1 water by-pass hose from the cylinder block.

  18. REMOVE NO. 1 EGR PIPE (w/ EGR System)


    1. A01H6XM

      Remove the 2 bolts and No. 1 EGR pipe.

  19. REMOVE NO. 3 WATER BY-PASS PIPE (w/o EGR System)


    1. A01COD6

      Remove the 2 bolts and No. 3 water by-pass pipe.

  20. REMOVE ENGINE WATER PUMP ASSEMBLY

    Click here

  21. REMOVE WATER INLET

    Click here

  22. REMOVE THERMOSTAT

    Click here

  23. REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)

    Click here

  24. REMOVE WATER INLET HOUSING


    1. A01H5LX

      Remove the 3 bolts, nut and water inlet housing from the cylinder block.

    2. A01CN6B

      Remove the gasket.

    3. A01CMV3

      Using an E6 "TORX" socket wrench, remove the 2 stud bolts from the water inlet housing.

      Note

      If a stud bolt is deformed or its thread is damaged, replace it.

  25. REMOVE INTAKE MANIFOLD


    1. B002KUB

      Slide the clamp and disconnect the No. 2 PCV hose from the intake manifold.

    2. B002KIQ

      Slide the clamp and disconnect the purge line hose from the intake manifold.

    3. B002IMC

      Remove the 6 bolts and intake manifold.

    4. B002KUS

      Remove the No. 1 intake manifold to head gasket from the intake manifold.

  26. REMOVE FUEL DELIVERY PIPE

    Click here

  27. REMOVE INJECTOR VIBRATION INSULATOR

    Click here

  28. REMOVE SENSOR WIRE


    1. A01CRHD

      Disconnect the knock control sensor connector.

    2. Remove the bolt and sensor wire.

  29. REMOVE IGNITION COIL ASSEMBLY

    Click here