АВТОМАТИЧЕСКАЯ ТРАНСМИССИЯ В БЛОКЕ С ГЛАВНОЙ ПЕРЕДАЧЕЙ УСТАНОВКА

PROCEDURE


  1. INSTALL TORQUE CONVERTER ASSEMBLY


    1. A00292IC01
      *a Matchmark
      *b Key

      Turn the front oil pump drive gear so that the key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.

    2. A0028YGC02
      *a Groove
      *b Matchmark

      Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.

    3. A0028OCC01
      *1 Front Oil Pump Oil Seal
      *a Matchmark

      Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

      Note


      • Install the torque converter assembly to the input shaft while keeping it horizontal.

      • Do not damage the front oil pump oil seal.

    4. A002902C01
      *1 Front Oil Pump Oil Seal
      *a Matchmark

      Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

      Note


      • Install the torque converter assembly to the input shaft while keeping it horizontal.

      • Do not damage the front oil pump oil seal.

    5. A002CKRC01
      *1 Front Oil Pump Oil Seal
      *a Matchmark

      Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the groove of the torque converter assembly into the key of the front oil pump drive gear.

      Note


      • Do not push the torque converter assembly excessively when rotating it.

      • Install the torque converter assembly to the input shaft while keeping it horizontal.

      • Do not damage the front oil pump oil seal.

    6. Clean the drive plate and torque converter assembly setting bolt holes.

    7. A0029B8C02
      *a Engine Surface
      *b Drive Plate Surface

      Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.

    8. A002CLNN01

      Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

      Standard
      A + 1 mm (0.0394 in.) or more

      Note


      • Make sure to deduct the thickness of the straightedge.

      • If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

      • Do not include the thickness of the set block.

  2. INSTALL SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY


    1. Apply ATF to a new O-ring and install it to the speedometer driven hole (ATM) cover sub-assembly.

      Note

      Ensure that the O-ring are not twisted.

    2. Install the speedometer driven hole (ATM) cover sub-assembly to the automatic transaxle assembly with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      Make sure that the O-ring is not damaged or does not jump out of the position during installation.

  3. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  4. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the 4 wire harness clamp brackets to the automatic transaxle assembly with the 4 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL FRONT ENGINE MOUNTING BRACKET


    1. Install the front engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  6. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY


    1. A002BO3

      Clean and degrease the bolt and bolt hole in the automatic transaxle assembly.

    2. A002ABQC01
      *1 Crankshaft
      *2 Torque Converter Assembly Centerpiece

      Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

      Clutch Spline Grease
      Toyota Genuine Clutch Spline Grease or equivalent
      Maximum Grease Amount
      Approximately 1 g (0.0353 oz)
    3. A0029LJC01
      *a Knock Pin

      While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and temporarily install the 10 bolts shown in the illustration.

      Torque:
      Bolt (A)
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }
      Bolt (B)
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }
      Bolt (C)
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Note


      • Confirm that the 2 knock pins are installed to the automatic transaxle assembly contact surface of the engine cylinder block before installing the automatic transaxle assembly.

      • Do not forcibly pry on the automatic transaxle assembly.

      • Check that the torque converter assembly rotates.

      Tech Tips

      Bolt length:


      • Bolt (A): 55 mm (2.17 in.)

      • Bolt (B): 50 mm (1.97 in.)

      • Bolt (C): 33 mm (1.30 in.)

    4. B003ZF3C48
      *a Adhesive

      Apply a few drops of adhesive to 2 or 3 threads at the tip of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

      Note

      Make sure to install the bolt immediately after applying adhesive to prevent foreign matter from attaching to it.

    5. A002BO3N02

      Install the bolt.

      Torque:
      Bolt (D)
      46 N*m  { 469 kgf*cm, 34 ft.*lbf }

      Tech Tips

      Bolt length:


      • Bolt (D): 41 mm (1.61 in.)

  7. INSTALL RADIATOR PIPE CLAMP


    1. Install the clamp to the radiator pipe clamp.

    2. Install the radiator pipe clamp with the clamp to the engine assembly with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Engage the breather plug to the clamp.

    4. Engage the air fuel ratio sensor wire harness.

  8. CONNECT WIRE HARNESS


    1. A00287RC03
      *a Park/Neutral Position Switch Connector

      Engage the 5 clamps to the automatic transaxle assembly.

    2. Connect the wire harness to the automatic transaxle assembly with the 2 bolts.

      Torque:
      Bolt (A)
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }
      Bolt (B)
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

    3. Connect the park/neutral position switch connector.

  9. INSTALL TCM

    Click here

  10. INSTALL MANIFOLD STAY

    Click here

  11. INSTALL FRONT FRAME ASSEMBLY

    Click here

  12. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    Click here

  13. INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT


    1. B003ZF3C48
      *a Adhesive

      Apply a few drops of adhesive to 2 or 3 threads at the tip of the 6 drive plate and torque converter assembly setting bolts.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

      Note

      Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.

    2. Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.

  14. INSTALL FLYWHEEL HOUSING UNDER COVER

    Click here

  15. CHECK AUTOMATIC TRANSAXLE SYSTEM

    Note

    If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

    Click here