АВТОМАТИЧЕСКАЯ ТРАНСМИССИЯ В БЛОКЕ С ГЛАВНОЙ ПЕРЕДАЧЕЙ СНЯТИЕ

CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

Note

If automatic transaxle parts are replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click here

PROCEDURE


  1. REMOVE FLYWHEEL HOUSING UNDER COVER

    Click here

  2. REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT


    1. A0026Z1

      Turn the crankshaft to gain access to the removable locations of the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

      Tech Tips

      There will be one black colored bolt.

  3. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

    Click here

  4. INSTALL ENGINE HANGERS

    Click here

  5. REMOVE FRONT FRAME ASSEMBLY

    Click here

  6. REMOVE MANIFOLD STAY

    Click here

  7. REMOVE TCM

    Click here

  8. DISCONNECT WIRE HARNESS


    1. A00287RC02
      *a Park/Neutral Position Switch Connector

      Disconnect the park/neutral position switch connector.

    2. Remove the 2 bolts and disengage the 5 clamps to disconnect the wire harness from the automatic transaxle assembly.

  9. REMOVE RADIATOR PIPE CLAMP


    1. A002ALFC01
      *1 Breather Plug
      *2 Radiator Pipe Clamp
      *a Air Fuel Ratio Sensor Wire Harness

      Disengage the air fuel ratio sensor wire harness.

    2. Disengage the breather plug from the clamp.

    3. Remove the bolt and radiator pipe clamp with the clamp from the engine assembly.

    4. A002757

      Remove the clamp from the radiator pipe clamp.

  10. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY


    1. Using a transmission jack attachment, set the automatic transaxle assembly on a transmission jack.

      Note


      • Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.

      • To prevent the automatic transaxle oil pan sub-assembly from deforming, do not place any attachments under the automatic transaxle oil pan sub-assembly.

      • Hold the engine assembly with a suitable adapter, such as a rope, during the operation.

    2. A0027N4

      Remove the 11 bolts and automatic transaxle assembly.

      Note

      To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.

  11. REMOVE FRONT ENGINE MOUNTING BRACKET


    1. A0026WP

      Remove the 3 bolts and front engine mounting bracket from the automatic transaxle assembly.

  12. REMOVE WIRE HARNESS CLAMP BRACKET


    1. A0027AD

      Remove the 4 bolts and 4 wire harness clamp brackets from the automatic transaxle assembly.

  13. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. A0027QR

      Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.

  14. REMOVE SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY


    1. A002CJ9

      Remove the bolt and speedometer driven hole (ATM) cover sub-assembly from the automatic transaxle assembly.

    2. Remove the O-ring from the speedometer driven hole (ATM) cover sub-assembly.

  15. REMOVE TORQUE CONVERTER ASSEMBLY


    1. A0028YB

      Remove the torque converter assembly from the automatic transaxle assembly.

      Note

      Remove the torque converter assembly from the input shaft horizontally.

  16. INSPECT TORQUE CONVERTER ASSEMBLY

    Click here

  17. INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

    Click here