REAR WIPER MOTOR REMOVAL

PROCEDURE


  1. PRECAUTION (for Glass Hatch Type)

    Note


    • Be sure to use the centering jig when removing and installing the rear wiper motor assembly. Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly, causing the wiping angle to change.

    • After installing the rear wiper motor assembly, do not open the glass hatch before installing the rear wiper link.

    • If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.

  2. REMOVE BACK WINDOW UPPER TRIM PANEL

    Click here

  3. REMOVE BACK DOOR TRIM COVER LH

    Click here

  4. REMOVE BACK DOOR TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)

    Click here

  6. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER

    Click here

  7. REMOVE NO. 1 BACK DOOR SERVICE HOLE COVER

    Click here

  8. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

    Click here

  9. REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type)


    1. A00288BC01
      B004057 Fastener

      Disengage the 3 clips.

    2. Disengage the fastener and remove the rear wiper shaft cover.

  10. REMOVE REAR WIPER ARM HEAD CAP


    1. A0027LK

      Disengage the 2 claws as shown in the illustration.

    2. A002ARD

      Disengage the 2 claws and remove the rear wiper arm head cap.

  11. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    1. A00290R

      Remove the nut and rear wiper arm and blade assembly.

  12. REMOVE REAR WIPER MOTOR GROMMET (for Fixed Glass Type)


    1. A0028SC

      Remove the rear wiper motor grommet.

  13. REMOVE REAR WIPER LINK CAP (for Glass Hatch Type)


    1. A0029GC

      Remove the rear wiper link cap.

  14. REMOVE REAR WIPER LINK PIVOT WITH WASHER PACKING (for Glass Hatch Type)


    1. A0029WZ

      Remove the nut and rear wiper link pivot with washer packing.

  15. REMOVE REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)


    1. A002BYM

      Disconnect the connector.

    2. Loosen the 4 bolts and remove the rear wiper motor assembly.

      Note

      Be careful not to scratch the back door glass.

  16. REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)


    1. When reusing the rear wiper motor assembly:


      1. Open the glass hatch.

      2. A0028RH

        Engage the 3 claws and 2 guides to install the centering jig.

        Note


        • The centering jig cannot be reused.

        • Do not remove the centering jig before installing the rear wiper link.

      3. A0029GI

        Close the glass hatch and engage the 2 claws and guide.

        Note

        Be sure to engage the 2 claws and guide securely.

      4. A0028P0C01
        B003Z8F Nut
        B003ZMU Bolt

        Disconnect the connector.

      5. Remove the 2 nuts.

      6. Remove the 4 bolts and rear wiper motor assembly.

        Note


        • Do not hold the rear wiper motor assembly by the rear wiper link.

        • Be careful not to scratch the back door glass.

    2. When using a new rear wiper motor assembly:


      1. A0027TA

        Disconnect the connector.

      2. Remove the 4 bolts.

      3. A0028FB

        Remove the 2 nuts and rear wiper motor assembly.

        Note

        Be careful not to scratch the back door glass.