OUTER MIRROR SWITCH INSPECTION

PROCEDURE

1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)

   
   

   1. Check the mirror select switch and mirror surface adjust switch. (w/o Retract Mirror)

      
      
      1. 

         *a	Mirror Select and Surface Adjust Switch
         *b	Component without harness connected (Outer Mirror Switch Assembly)

         Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for left side)
         Tester Connection Condition Specified Condition 12 (VL) - 15 (B) 9 (M+) - 7 (E) Up Below 1 Ω Off 10 kΩ or higher 12 (VL) - 7 (E) 9 (M+) - 15 (B) Down Below 1 Ω Off 10 kΩ or higher 13 (HL) - 15 (B) 9 (M+) - 7 (E) Left Below 1 Ω Off 10 kΩ or higher 13 (HL) - 7 (E) 9 (M+) - 15 (B) Right Below 1 Ω Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for right side)
         Tester Connection Condition Specified Condition 10 (VR) - 15 (B) 9 (M+) - 7 (E) Up Below 1 Ω Off 10 kΩ or higher 10 (VR) - 7 (E) 9 (M+) - 15 (B) Down Below 1 Ω Off 10 kΩ or higher 11 (HR) - 15 (B) 9 (M+) - 7 (E) Left Below 1 Ω Off 10 kΩ or higher 11 (HR) - 7 (E) 9 (M+) - 15 (B) Right Below 1 Ω Off 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

   2. Check the mirror select switch and mirror surface adjust switch. (w/ Retract Mirror)

      
      
      1. 

         *a	Mirror Select and Surface Adjust Switch
         *b	Component without harness connected (Outer Mirror Switch Assembly)

         Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for left side)
         Tester Connection Condition Specified Condition 10 (VL) - 7 (B) 13 (M+) - 15 (E) Up Below 1 Ω Off 10 kΩ or higher 10 (VL) - 15 (E) 13 (M+) - 7 (B) Down Below 1 Ω Off 10 kΩ or higher 9 (HL) - 7 (B) 13 (M+) - 15 (E) Left Below 1 Ω Off 10 kΩ or higher 9 (HL) - 15 (E) 13 (M+) - 7 (B) Right Below 1 Ω Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for right side)
         Tester Connection Condition Specified Condition 12 (VR) - 7 (B) 13 (M+) - 15 (E) Up Below 1 Ω Off 10 kΩ or higher 12 (VR) - 15 (E) 13 (M+) - 7 (B) Down Below 1 Ω Off 10 kΩ or higher 11 (HR) - 7 (B) 13 (M+) - 15 (E) Left Below 1 Ω Off 10 kΩ or higher 11 (HR) - 15 (E) 13 (M+) - 7 (B) Right Below 1 Ω Off 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

   3. Check the mirror retract switch. (w/ Retract Mirror)

      
      
      1. 

         *a	Mirror Retract Switch
         *b	Component without harness connected (Outer Mirror Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 4 (MF) - 5 (E) AUTO position Below 1 Ω Except AUTO position 10 kΩ or higher 2 (MR) - 5 (E) Retract position Below 1 Ω Except retract position 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)

   
   

   1. Check the mirror select switch and mirror surface adjust switch. (w/o Retract Mirror)

      
      
      1. 

         *a	Mirror Select and Surface Adjust Switch
         *b	Component without harness connected (Outer Mirror Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection Condition Specified Condition 15 (M+) - 12 (E) Mirror surface adjust switch pushed up 90 to 110 Ω Mirror surface adjust switch pushed down 437 to 503 Ω Mirror surface adjust switch pushed left 744 to 856 Ω Mirror surface adjust switch pushed right 225 to 275 Ω Mirror surface adjust switch not pushed 10 kΩ or higher 13 (MSW) - 12 (E) Mirror select switch turned to R position Below 1 Ω Mirror select switch turned to L position 90 to 110 Ω Mirror select switch off 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

   2. Check the mirror select switch and mirror surface adjust switch. (w/ Retract Mirror)

      
      
      1. 

         *a	Mirror Select and Surface Adjust Switch
         *b	Component without harness connected (Outer Mirror Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection Condition Specified Condition 13 (M+) - 16 (E) Mirror surface adjust switch pushed up 90 to 110 Ω Mirror surface adjust switch pushed down 437 to 503 Ω Mirror surface adjust switch pushed left 744 to 856 Ω Mirror surface adjust switch pushed right 225 to 275 Ω Mirror surface adjust switch not pushed 10 kΩ or higher 15 (MSW) - 16 (E) Mirror select switch turned to R position Below 1 Ω Mirror select switch turned to L position 90 to 110 Ω Mirror select switch off 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

   3. Check that the switch functions. (w/ Retract Mirror)

      
      
      1. 

         *a	Mirror Retract Switch
         *b	Component without harness connected (Outer Mirror Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 17 (MF) - 18 (E) AUTO position Below 1 Ω Except AUTO position 10 kΩ or higher 11 (MR) - 18 (E) Retract position Below 1 Ω Except retract position 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.