POWER MIRROR CONTROL SYSTEM(w/o Memory) Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

DESCRIPTION

The outer mirror switch assembly sends a mirror retract/return signal to the main body ECU (multiplex network body ECU) when the retractable outer mirror switch on the outer mirror switch assembly is operated. The main body ECU (multiplex network body ECU) retracts or returns the outer rear view mirror assemblies based on the signal.

WIRING DIAGRAM

A002801E01

CAUTION / NOTICE / HINT

Note


  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*


    • *: w/ Smart Entry and Start System

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

    Click here


    • *: for LHD

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Outer Mirror Fold SW Retractable outer mirror switch signal OFF or ON

      OFF: Retractable outer mirror switch off

      ON: Retractable outer mirror switch on

      		 -

      Body Electrical > Main Body > Data List
      Tester Display
      Outer Mirror Fold SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  2. PERFORM ACTIVE TEST USING GTS


    1. Enter the following menus: Body Electrical / Main Body / Active Test.

    2. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Mirror Fold Retract mirror operation OFF or ON -
      Mirror Return Retract mirror operation OFF or ON -

      Body Electrical > Main Body > Active Test
      Tester Display
      Mirror Fold

      Body Electrical > Main Body > Active Test
      Tester Display
      Mirror Return
      Result
      Result Proceed to
      Both outer rear view mirror assemblies operate normally A
      Outer rear view mirror assembly LH does not operate normally B
      Outer rear view mirror assembly RH does not operate normally C
      Both outer rear view mirror assemblies do not operate normally D

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    D

    INSPECT MIR RTR NO. 1 / NO. 2 RELAY Click here

    B

  3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. Remove the outer rear view mirror assembly LH.

      Click here

    2. Inspect the outer rear view mirror assembly LH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (MIR RTR NO. 1 / NO. 2 RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH)


    1. A0026W5C01
      *1 Relay Block No. 5
      *a MIR RTR NO. 1 Relay terminals
      *b MIR RTR NO. 2 Relay terminals

      Remove the MIR RTR NO. 1 relay from the relay block No. 5.

    2. Remove the MIR RTR NO. 2 relay from the relay block No. 5.

    3. Disconnect the I1 outer rear view mirror assembly LH connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 - I1-3 (MR) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 - I1-8 (MF) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 or I1-3 (MR) - Body Ground Always 10 kΩ or higher
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 or I1-8 (MF) - Body Ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


    1. Remove the outer rear view mirror assembly RH.

      Click here

    2. Inspect the outer rear view mirror assembly RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (MIR RTR NO. 1 / NO. 2 RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH)


    1. A0026W5C01
      *1 Relay Block No. 5
      *a MIR RTR NO. 1 Relay terminals
      *b MIR RTR NO. 2 Relay terminals

      Remove the MIR RTR NO. 1 relay from the relay block No. 5.

    2. Remove the MIR RTR NO. 2 relay from the relay block No. 5.

    3. Disconnect the H1 outer rear view mirror assembly RH connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 - H1-3 (MR) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 - H1-8 (MF) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 or H1-3 (MR) - Body Ground Always 10 kΩ or higher
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 or H1-8 (MF) - Body Ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. INSPECT MIR RTR NO. 1 / NO. 2 RELAY


    1. Inspect the MIR RTR NO. 1 relay.

      Click here

    2. Inspect the MIR RTR NO. 2 relay.

      Click here

      Result
      Result Proceed to
      OK A
      NG (MIR RTR NO. 1 Relay) B
      NG (MIR RTR NO. 2 Relay) C

    B

    REPLACE MIR RTR NO. 1 RELAY

    C

    REPLACE MIR RTR NO. 2 RELAY

    A

  8. CHECK HARNESS AND CONNECTOR (MIR RTR NO. 1 / NO. 2 RELAY POWER SOURCE)


    1. A0026W5C01
      *1 Relay Block No. 5
      *a MIR RTR NO. 1 Relay terminals
      *b MIR RTR NO. 2 Relay terminals

      Remove the MIR RTR NO. 1 relay from the relay block No. 5.

    2. Remove the MIR RTR NO. 2 relay from the relay block No. 5.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Relay block No. 5 MIR RTR NO. 1 relay terminal 1 - Body ground Always 11 to 14 V
      Relay block No. 5 MIR RTR NO. 2 relay terminal 1 - Body ground Always 11 to 14 V
      Relay block No. 5 MIR RTR NO. 1 relay terminal 5 - Body ground Always 11 to 14 V
      Relay block No. 5 MIR RTR NO. 2 relay terminal 5 - Body ground Always 11 to 14 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Relay block No. 5 MIR RTR NO. 1 relay terminal 4 - Body ground Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 2 relay terminal 4 - Body ground Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 1 relay terminal 4 - relay block No. 5 MIR RTR NO. 2 relay terminal 4 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - MIR RTR NO. 1 / NO. 2 RELAY)


    1. A0026W5C01
      *1 Relay Block No. 5
      *a MIR RTR NO. 1 Relay terminals
      *b MIR RTR NO. 2 Relay terminals

      Remove the MIR RTR NO. 1 relay from the relay block No. 5.

    2. Remove the MIR RTR NO. 2 relay from the relay block No. 5.

    3. Disconnect the F18 main body ECU (multiplex network body ECU) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Relay block No. 5 MIR RTR NO. 1 relay terminal 2 - F18-19 (RETR) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 2 relay terminal 2 - F18-20 (RTRR) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 1 relay terminal 2 or F18-19 (RETR) - Body Ground Always 10 kΩ or higher
      Relay block No. 5 MIR RTR NO. 2 relay terminal 2 or F18-20 (RTRR) - Body Ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH/RH - MIR RTR NO. 1 / NO. 2 RELAY)


    1. A0026W5C01
      *1 Relay Block No. 5
      *a MIR RTR NO. 1 Relay terminals
      *b MIR RTR NO. 2 Relay terminals

      Remove the MIR RTR NO. 1 relay from the relay block No. 5.

    2. Remove the MIR RTR NO. 2 relay from the relay block No. 5.

    3. Disconnect the I1 outer rear view mirror assembly LH connector.

    4. Disconnect the H1 outer rear view mirror assembly RH connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 - I1-3 (MR) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 - H1-3 (MR) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 - I1-8 (MF) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 - H1-8 (MF) Always Below 1 Ω
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 or H1-3 (MR) - Body Ground Always 10 kΩ or higher
      Relay block No. 5 MIR RTR NO. 1 relay terminal 3 or I1-3 (MR) - Body Ground Always 10 kΩ or higher
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 or H1-8 (MF) - Body Ground Always 10 kΩ or higher
      Relay block No. 5 MIR RTR NO. 2 relay terminal 3 or I1-8 (MF) - Body Ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  11. INSPECT OUTER MIRROR SWITCH ASSEMBLY


    1. Remove the outer mirror switch assembly.

      Click here

    2. Inspect the outer mirror switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  12. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    1. Disconnect the I9 outer mirror switch assembly.

    2. Disconnect the F18 main body ECU (multiplex network body ECU).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I9-2 (MR) - F18-14 (RET) Always Below 1 Ω
      I9-2 (MR) or F18-14 (RET) - Body ground Always 10 kΩ or higher
      I9-5 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR