POWER MIRROR CONTROL SYSTEM(w/ Memory) Power Mirrors do not Return to Memorized Position

DESCRIPTION

If any of the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. The main body ECU (multiplex network body ECU) sends the reproduction signal to each outer mirror control ECU assembly via CAN communication. When receiving the reproduction signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly, to adjust the mirror surface to the stored position.

WIRING DIAGRAM


  1. for LHD

    A0029AKE07

  2. for RHD

    A0029AKE08

CAUTION / NOTICE / HINT

Note


  • The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

    Click here


    • *: for LHD

PROCEDURE


  1. CHECK SEAT MEMORY SWITCH FUNCTION


    1. When any seat memory switch (M1 or M2) is pressed, check that the driver seat moves to the memorized position.

      Click here

      OK
      Driver seat moves to the memorized position.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO FRONT POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position) Click here

    OK

  2. CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION


    1. Check the electrical remote control mirror function.

      Click here

      OK
      Electrical remote control mirror function is normal.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirror cannot be Adjusted with Power Mirror Switch) Click here

    OK

  3. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Mirror L*1 or Mirror R*2 / Data List.


      • *1: for LHD

      • *2: for RHD

    5. Read the Data List according to the display on the GTS.


      1. for LHD


        Body Electrical > Mirror L > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.3 Mirror position memorized in memory switch M3* OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 Not applicable

        • *: Although the item is displayed on the GTS, it is not applicable to this vehicle.


        Body Electrical > Mirror L > Data List
        Tester Display
        Mirror Memory No.1
        Mirror Memory No.2
        Mirror Memory No.3

      2. for RHD


        Body Electrical > Mirror R > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 -
        Mirror Memory No.3 Mirror position memorized in memory switch M3* OFF or ON

        OFF: Not memorized

        ON: Memorized

        		 Not applicable

        • *: Although the item is displayed on the GTS, it is not applicable to this vehicle.


        Body Electrical > Mirror R > Data List
        Tester Display
        Mirror Memory No.1
        Mirror Memory No.2
        Mirror Memory No.3
      OK
      ON (Memorized) appears on the screen.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirror Surface Position is not Memorized) Click here

    OK

  4. CHECK MEMORY AND REACTIVATION FUNCTION


    1. A0029PPC13
      *a Turn to Fully Left Position

      Turn the ignition switch to ON.

    2. Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

    3. Press the M1 switch while the SET switch is being pressed.

    4. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

    5. Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

    6. Press the M1 switch.

    7. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.

      Result
      Result Proceed to
      Memory and reactivation functions on both mirrors are not normal A
      Memory and reactivation function on driver door mirror is not normal B
      Memory and reactivation function on front passenger door mirror is not normal C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) Click here

    B

  5. REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)


    1. Temporarily replace the outer rear view mirror assembly (driver door) with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK MEMORY AND REACTIVATION FUNCTION


    1. A0029PPC13
      *a Turn to Fully Left Position

      Turn the ignition switch to ON.

    2. Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

    3. Press the M1 switch while the SET switch is being pressed.

    4. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

    5. Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

    6. Press the M1 switch.

    7. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.

      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) Click here

  7. REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)


    1. Temporarily replace the outer rear view mirror assembly (front passenger door) with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  8. CHECK MEMORY AND REACTIVATION FUNCTION


    1. A0029PPC13
      *a Turn to Fully Left Position

      Turn the ignition switch to ON.

    2. Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

    3. Press the M1 switch while the SET switch is being pressed.

    4. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

    5. Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

    6. Press the M1 switch.

    7. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.

      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) Click here