POWER MIRROR CONTROL SYSTEM(w/ Memory) Power Mirror cannot be Adjusted with Power Mirror Switch

DESCRIPTION

The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the each outer mirror control ECU assembly via CAN communication. Based on this signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors to adjust the mirror surface position.

WIRING DIAGRAM

A018L8GE23

CAUTION / NOTICE / HINT

Note


  • The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

    Click here


    • *: for LHD

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Mirror Selection SW (R) Mirror select switch signal for RH mirror OFF or ON

      OFF: Mirror select switch off

      ON: Mirror select switch R switch on

      		 -
      Mirror Selection SW (L) Mirror select switch signal for LH mirror OFF or ON

      OFF: Mirror select switch off

      ON: Mirror select switch L switch on

      		 -
      Mirror Position SW (R) Mirror adjust switch signal (Right) OFF or ON

      OFF: Mirror adjust switch not pushed right

      ON: Mirror adjust switch pushed right

      		 Check with the mirror select switch L or R selected
      Mirror Position SW (L) Mirror adjust switch signal (Left) OFF or ON

      OFF: Mirror adjust switch not pushed left

      ON: Mirror adjust switch pushed left

      		 Check with the mirror select switch L or R selected
      Mirror Position SW (Up) Mirror adjust switch signal (Up) OFF or ON

      OFF: Mirror adjust switch not pushed up

      ON: Mirror adjust switch pushed up

      		 Check with the mirror select switch L or R selected
      Mirror Position SW (Dwn) Mirror adjust switch signal (Down) OFF or ON

      OFF: Mirror adjust switch not pushed down

      ON: Mirror adjust switch pushed down

      		 Check with the mirror select switch L or R selected

      Body Electrical > Main Body > Data List
      Tester Display
      Mirror Selection SW (R)
      Mirror Selection SW (L)
      Mirror Position SW (R)
      Mirror Position SW (L)
      Mirror Position SW (Up)
      Mirror Position SW (Dwn)
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY


    1. Remove the outer mirror switch assembly.

      Click here

    2. Inspect the outer mirror switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    1. Disconnect the I10*1 or H11*2 outer mirror switch assembly.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the F20 main body ECU (multiplex network body ECU).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      I10-16 (E) - F20-6 (MIRE) Always Below 1 Ω
      I10-13 (M+) - F20-4 (MIRB) Always Below 1 Ω
      I10-15 (MSW) - F20-5 (MIRS) Always Below 1 Ω
      I10-16 (E) or F20-6 (MIRE) - Body ground Always 10 kΩ or higher
      I10-13 (M+) or F20-4 (MIRB) - Body ground Always 10 kΩ or higher
      I10-15 (MSW) or F20-5 (MIRS) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      H11-12 (E) - F20-6 (MIRE) Always Below 1 Ω
      H11-15 (M+) - F20-4 (MIRB) Always Below 1 Ω
      H11-13 (MSW) - F20-5 (MIRS) Always Below 1 Ω
      H11-12 (E) or F20-6 (MIRE) - Body ground Always 10 kΩ or higher
      H11-15 (M+) or F20-4 (MIRB) - Body ground Always 10 kΩ or higher
      H11-13 (MSW) or F20-5 (MIRS) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR