POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Front Door Windows) Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly (for rear RH door) is operated by the rear power window regulator switch assembly (for RH door).

WIRING DIAGRAM

A018LFUE06

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) - BATTERY)


    1. Disconnect the J5 rear power window regulator switch assembly (for RH door) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J5-2 (B) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)


    1. Remove the rear power window regulator switch assembly (for RH door).

      Click here

    2. Inspect the rear power window regulator switch assembly (for RH door).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR))


    1. Disconnect the J1 power window regulator motor assembly (for rear RH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J5-7 (U) - J1-2 (U) Always Below 1 Ω
      J5-7 (U) or J1-2 (U) - Body ground Always 10 kΩ or higher
      J5-1 (D) - J1-1 (D) Always Below 1 Ω
      J5-1 (D) or J1-1 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. Remove the power window regulator master switch assembly.

      Click here

    2. Inspect the power window regulator master switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H6-10 (RRU) - J5-3 (SU) Always Below 1 Ω
      H6-10 (RRU) or J5-3 (SU) - Body ground Always 10 kΩ or higher
      H6-16 (RRD) - J5-4 (SD) Always Below 1 Ω
      H6-16 (RRD) or J5-4 (SD) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR