ROOF HEADLINING REMOVAL

PROCEDURE


  1. REMOVE DECK BOARD ASSEMBLY


    1. Remove the deck board assembly.

  2. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. Remove the No. 3 deck board sub-assembly.

  3. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  4. REMOVE DECK SIDE TRIM BOX LH


    1. Fold the rear No. 2 seatback assembly LH forward.

    2. B00404Z

      Disengage the 4 claws, clip and guide to remove the deck side trim box LH.

  5. REMOVE REAR DECK FLOOR BOX


    1. Fold the rear No. 2 seatback assembly RH forward.

    2. B003YYB

      Using a clip remover, remove the 7 clips.

    3. B004022

      Remove the nut.

    4. Disengage the 4 claws, 2 clips and 2 guides to remove the rear deck floor box.

  6. REMOVE REAR FLOOR FINISH PLATE


    1. B003Z2AN01

      Disengage the 2 claws (A).

    2. Disengage the 6 claws (B) and 2 guides.

    3. Disengage the 4 clips to remove the rear floor finish plate.

  7. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B003ZLLN01

      Disengage the 2 claws (A).

    2. Disengage the 8 claws (B) and 2 guides to remove the front door scuff plate LH.

  9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. B003ZTM

      Remove the clip.

    2. Disengage the claw and clip to remove the cowl side trim sub-assembly LH as shown in the illustration.

  10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip LH.

  11. REMOVE FRONT PILLAR GARNISH LH


    1. B003ZTDC01
      *a Front Pillar Garnish Clip (A)
      *b Front Pillar Garnish Clip (B)
      B004057 Protective Tape

      Apply protective tape around the front pillar garnish LH as shown in the illustration.

    2. Pull the upper part of the front pillar garnish LH toward the inside of the cabin and disengage the front pillar garnish LH from the base of the 2 front pillar garnish clips.

      Tech Tips

      Let the front pillar garnish LH hang from the 2 front pillar garnish clips.

    3. B003ZIU

      While pushing the tabs on the front pillar garnish clip (A) in the direction indicated by the arrow shown in the illustration, disengage the front pillar garnish clip (A).

      Note

      A front pillar garnish clip (A) is reusable if it is not damaged.

    4. B003ZASC01
      *a Protective Tape
      *b 90°

      Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip (B) 90° in the direction indicated by the arrow (1) shown in the illustration.

    5. Pull the front pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage it from the front pillar garnish clip (B).

      Note


      • A front pillar garnish clip (B) is reusable if it is not removed from the vehicle and is not damaged.

      • Replace the front pillar garnish clip (B) with a new one if it is removed from the vehicle.

    6. Pull the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration to disengage the 2 guides to remove the front pillar garnish LH.

    7. B003YYVC01
      *1 Curtain Shield Airbag Assembly LH
      *a Protective Cover
      *b Adhesive Tape

      Protect the curtain shield airbag assembly LH.


      1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  12. REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH

    Click here

  13. REMOVE REAR DOOR SCUFF PLATE LH


    1. Lift up the rear seat adjusting handle and move the rear No. 1 seat assembly LH to the foremost position.

    2. B003ZLQ

      Using a moulding remover, disengage the 2 clips.

    3. B00406AN01

      Disengage the claw (A).

    4. Disengage the 5 claws (B), 2 clips and 2 guides to remove the rear door scuff plate LH.

  14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip LH.

  15. REMOVE LOWER CENTER PILLAR GARNISH LH


    1. B003ZP9N01

      Disengage the 2 claws (A).

    2. Disengage the 2 claws (B) and 2 clips to remove the lower center pillar garnish LH.

  16. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

  17. REMOVE CENTER PILLAR GARNISH LH


    1. B00408U

      Remove the screw.

    2. Disengage the 2 clips.

    3. Pass the anchor of the front seat outer belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.

  18. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  20. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  23. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  24. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  25. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  26. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  27. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  28. REMOVE FRONT DECK SIDE TRIM COVER LH


    1. B003ZOZ

      Disengage the 2 claws and guide to remove the front deck side trim cover LH as shown in the illustration.

  29. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

    Click here

  30. REMOVE NO. 2 DECK SIDE TRIM COVER


    1. B004068

      Disengage the 6 claws, clip and 2 guides to remove the No. 2 deck side trim cover.

  31. REMOVE DECK TRIM SIDE SERVICE HOLE COVER


    1. B003ZYS

      Disengage the claw and 2 guides to remove the deck trim side service hole cover.

  32. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

    Click here

  33. REMOVE DECK TRIM POCKET COVER (for LH Side)


    1. B003ZTC

      Using a moulding remover, disengage the 2 claws to remove the deck trim pocket cover.

  34. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)


    1. B003YWN

      Turn the No. 1 luggage compartment trim hook as shown in the illustration to remove it.

  35. REMOVE ROPE HOOK (for LH Side)


    1. B003YXB

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. Remove the 2 bolts and 2 rope hooks.

  36. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 3 bolts.

      B003Z9BN01

    2. Disengage the 2 clips (A).

    3. Disengage the 3 clips (B) and guide (A).

      Tech Tips

      Disengage the clips (B) and guide (A) from the rear side of the deck trim side panel assembly LH.

    4. Disengage the claw.

    5. Disengage the 5 clips (C) and guide (B) to remove the deck trim side panel assembly LH.

      Tech Tips

      Disengage the clips (C) and guide (B) from the upper side of the deck trim side panel assembly LH.

  37. REMOVE QUARTER PILLAR GARNISH LH


    1. B003Z1LN01

      Disengage the clip (A).

    2. Disengage the claw.

    3. Disengage the clip (B) and guide.

    4. Pass the anchor of the rear No. 1 seat outer belt assembly LH through the quarter pillar garnish LH and remove the quarter pillar garnish LH.

  38. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH


    1. B003ZQNN01

      Disengage the 2 clips (A).

    2. Disengage the 2 clips (B) and claw.

    3. Pass the anchor of the rear No. 2 seat outer belt assembly LH through the inner roof side garnish assembly LH and remove the inner roof side garnish assembly LH.

  39. REMOVE FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  40. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  41. REMOVE NO. 1 DECK SIDE TRIM COVER


    1. B003ZKE

      Disengage the 5 claws, clip and 2 guides to remove the No. 1 deck side trim cover.

  42. REMOVE DECK TRIM SIDE BELT HOLE COVER RH


    1. B00408N

      Using a moulding remover, disengage the 4 claws and 2 guides to remove the deck trim side belt hole cover RH.

  43. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  44. REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)


    1. B003ZEI

      Using a moulding remover, disengage the 4 claws to remove the side trim cover RH.

  45. REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (w/ Rear Automatic Air Conditioning System)

    Click here

  46. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  47. REMOVE DECK TRIM POCKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  48. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  49. REMOVE ROPE HOOK (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  50. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the 3 bolts.

      B003YXHC01
      *A w/ Rear Automatic Air Conditioning System - -

    2. Disengage the 2 clips (A).

    3. Disengage the 3 clips (B) and guide (A).

      Tech Tips

      Disengage the clips (B) and guide (A) from the rear side of the deck trim side panel assembly RH.

    4. Disengage the claw.

    5. w/o Rear Automatic Air Conditioning System:


      1. Disengage the 5 clips (C) and guide (B) to remove the deck trim side panel assembly RH.

        Tech Tips

        Disengage the clips (C) and guide (B) from the upper side of the deck trim side panel assembly RH.

    6. w/ Rear Automatic Air Conditioning System:


      1. Disengage the 5 clips (C) and guide (B) to disconnect the deck trim side panel assembly RH.

        Tech Tips

        Disengage the clips (C) and guide (B) from the upper side of the deck trim side panel assembly RH.

      2. Disengage the clamp to remove the deck trim side panel assembly RH.

  51. REMOVE QUARTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  52. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  53. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  54. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  55. REMOVE RAIN SENSOR COVER (w/ Lane Departure Alert System)

    Click here

  56. REMOVE LANE DEPARTURE WARNING CAMERA COVER NO.1 (w/ Lane Departure Alert System)

    Click here

  57. REMOVE MAP LIGHT ASSEMBLY

    Click here

  58. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)

    Click here

  59. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)

    Click here

  60. REMOVE COOLER PLATE

    Click here

  61. REMOVE NO. 1 COOLER AIR DUCT

    Click here

  62. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for all assist grip sub-assemblies.


    1. B003ZIFC01
      *a Protective Tape

      Using a screwdriver, disengage the 2 claws and remove the assist grip cover LH.

      Note

      Do not forcibly pry the assist grip cover LH to prevent it from being deformed.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure for the RH side and LH side.

    2. B003ZID

      Disengage the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  63. REMOVE REAR ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure as for the assist grip sub-assembly.

  64. REMOVE VISOR BRACKET COVER (for LH Side)


    1. B003ZEF

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

  65. REMOVE VISOR ASSEMBLY LH


    1. B00406W

      for "TORX" Screw:


      1. Using a T25 "TORX" socket wrench, remove the 2 screws and visor assembly LH.

    2. except "TORX" Screw:


      1. Remove the 2 screws and visor assembly LH.

  66. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  67. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  68. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure for the LH side and RH side.


    1. B003ZOQC08
      *a 45°

      Turn the visor holder approximately 45° and pull it out as indicated by the arrows, in the order shown in the illustration.

    2. Disengage the 2 claws to remove the visor holder.

  69. DISCONNECT REAR ROOF SIDE RAIL GARNISH LH


    1. B003ZJ3

      Disengage the 3 clips to disconnect the rear roof side rail garnish LH as shown in the illustration.

  70. DISCONNECT REAR ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  71. REMOVE ROOF HEADLINING ASSEMBLY


    1. for Windshield Glass Side:


      1. Disconnect each connector.

    2. for Front Pillar LH Side (w/o Rear Seat Entertainment System):


      1. B003ZCI

        Disengage the 3 clamps.

      2. Disconnect the 2 connectors.

    3. for Front Pillar LH Side (w/ Rear Seat Entertainment System):


      1. B003ZWJ

        Disengage the 3 clamps.

      2. Disconnect the 3 connectors.

    4. for Front Pillar RH Side:


      1. B003ZWC

        Disengage the 3 clamps.

      2. Disconnect the connector.

      3. Disconnect the rear washer hose assembly.

    5. B003ZZLC01
      *a Clamp
      *b Guide

      for Rear Pillar LH Side (w/o DAB Function):


      1. Disconnect the connector.

      2. Remove the bolt.

      3. Disengage the clamp and 2 guides.

    6. B003ZV8C01
      *a Clamp
      *b Guide

      for Rear Pillar LH Side (w/ DAB Function):


      1. Disconnect the connector.

      2. Remove the 2 bolts.

      3. Disengage the 2 clamps and 4 guides.

    7. B00402IC01
      *a Clamp
      *b Guide

      for Rear Pillar RH Side:


      1. Disconnect the 2 connectors.

      2. Remove the 2 bolts.

      3. Disengage the 2 clamps and 3 guides.

      4. Disconnect the rear washer hose assembly.

    8. B00402T

      for Rear Side:


      1. Using a moulding remover, disengage the 3 clips.

    9. for Roof Side (for Normal Roof):

      B003ZXI

      1. Remove the 4 clips.

    10. for Roof Side (for Sliding Roof):

      B003ZYT

      1. Disconnect the connector from the sliding roof drive gear sub-assembly.

      2. Disengage the 12 fasteners.

      3. Remove the 2 clips.

    11. B003ZC5

      Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or body interior.