LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2785

DTC Code DTC Name
B2785 Communication Malfunction between ECUs Connected by LIN

DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN

  • Errors in LIN communication between ECUs or an open or short in communication lines.

  • LIN communication error detected by the certification ECU (smart key ECU assembly) 3 times in a row.

  • Certification ECU (smart key ECU assembly)

  • Steering lock ECU (steering lock actuator assembly)

  • ID code box (immobiliser code ECU)*

  • Wire harness or connector

  • STRG LOCK fuse

  • MPX-B NO. 2 fuse*

WIRING DIAGRAM

A018HDSE18

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the certification ECU (smart key ECU assembly) is replaced, refer to Service Bulletin.

  • If the steering lock ECU (steering lock actuator assembly) is replaced, refer to Service Bulletin.

  • If the ID code box (immobiliser code ECU) is replaced, refer to Service Bulletin. (for LHD)

  • Before performing the inspection, check that DTC B2786, B2789 or B278C is not output.

    Click here

  • When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)


    1. Disconnect the F13 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the F54 steering lock ECU (steering lock actuator assembly) connector.

    3. Disconnect the F67 ID code box (immobiliser code ECU) connector.*


      • *: for LHD

    4. Measure the resistance according to the value(s) in the table below.

      Note

      Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F13-6 (LIN) - F54-5 (LIN) Ignition switch off Below 1 Ω
      F13-6 (LIN) - F67-2 (LIN1)* Ignition switch off Below 1 Ω
      F13-6 (LIN) - Body ground Ignition switch off 10 kΩ or higher
      F54-5 (LIN) - Body ground Ignition switch off 10 kΩ or higher
      F67-2 (LIN1) - Body ground* Ignition switch off 10 kΩ or higher

      • *: for LHD

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))


    1. Reconnect the F13 certification ECU (smart key ECU assembly) connector.

    2. Reconnect the F67 ID code box (immobiliser code ECU) connector.*


      • *: for LHD

    3. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs

    4. Recheck for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Result Proceed to
      DTC B2785 is output (for LHD) A
      DTC B2785 is output (except LHD) B
      DTC B2785 is not output C

    B

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    C

    REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) Click here

    A

  3. CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))


    1. Reconnect the F54 steering lock ECU (steering lock actuator assembly) connector.

    2. Disconnect the F67 ID code box (immobiliser code ECU) connector.

    3. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs

    4. Recheck for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Result Proceed to
      DTC B2785 is output A
      DTC B2785 is not output B

    A

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    B

    REPLACE ID CODE BOX (IMMOBILISER CODE ECU)