ULTRASONIC SENSOR(for Rear Side) INSTALLATION

PROCEDURE


  1. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

    • If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one. Install the No. 1 ultrasonic sensor with a new rear corner ultrasonic sensor retainer as a set to the rear bumper assembly.

    • Use the same procedure for the RH side and LH side.


    1. A002CH7

      Engage the 2 claws and install a new rear corner ultrasonic sensor retainer to the No. 1 ultrasonic sensor.

    2. Clean the rear bumper assembly surface.


      1. Remove any remaining double-sided tape from the rear bumper assembly.

      2. Wipe off any tape adhesive residue with cleaner.

    3. A0027DLC03
      *a 18 mm (0.709 in.)

      Cover the sensor installation hole with a 18 mm (0.709 in.) circular piece of tape.

    4. A0029FNC01
      B003ZQH Primer

      Using a brush or felt, apply primer or equivalent to the rear corner ultrasonic sensor retainer installation area.

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    5. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.

    6. Peel off the release paper from the new rear corner ultrasonic sensor retainer.

    7. A002CLCC01
      *a Scribed line
      *b Protrusion of the mark

      Align the rear corner ultrasonic sensor retainer with No. 1 ultrasonic sensor with the mark on the rear bumper assembly and install it as shown in the illustration.

      Note


      • Ensure that the sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

      • Ensure that the rear corner ultrasonic sensor retainer is within the scribed line.

      • The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear corner ultrasonic sensor retainer with a new one when reattachment is necessary.

      Tech Tips


      • Align the connector with the protrusion of the mark when connecting it.

      • Press the rear corner ultrasonic sensor retainer with a force of 30 N (3.0 kgf) for 3 seconds and install the rear corner ultrasonic sensor retainer firmly so that there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper assembly.

  2. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

    • If a rear center ultrasonic sensor retainer has been removed, replace it with a new one. Install the No. 1 ultrasonic sensor with a new rear center ultrasonic sensor retainer as a set to the rear bumper assembly.

    • Use the same procedure for the RH side and LH side.


    1. A002ACY

      Engage the 2 claws and install a new rear center ultrasonic sensor retainer to the No. 1 ultrasonic sensor.

    2. Clean the rear bumper assembly surface.


      1. Remove any remaining double-sided tape from the rear bumper assembly.

      2. Wipe off any tape adhesive residue with cleaner.

    3. A0027DLC03
      *a 18 mm (0.709 in.)

      Cover the sensor installation hole with a 18 mm (0.709 in.) circular piece of tape.

    4. A0028OAC02
      B003ZQH Primer

      Using a brush or felt, apply primer or equivalent to the rear center ultrasonic sensor retainer installation area.

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    5. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.

    6. Peel off the release paper from the new rear center ultrasonic sensor retainer.

    7. A00285SC01
      *a Scribed line
      *b Protrusion of the mark

      Align the rear center ultrasonic sensor retainer with No. 1 ultrasonic sensor with the mark on the rear bumper assembly and install it as shown in the illustration.

      Note


      • Ensure that the sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

      • Ensure that the rear center ultrasonic sensor retainer is within the scribed line.

      • The double-sided tape of a rear center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear center ultrasonic sensor retainer with a new one when reattachment is necessary.

      Tech Tips


      • Align the connector with the protrusion of the mark when connecting it.

      • Press the rear center ultrasonic sensor retainer with a force of 30 N (3.0 kgf) for 3 seconds and install the rear center ultrasonic sensor retainer firmly so that there is no clearance between the rear center ultrasonic sensor retainer and rear bumper assembly.

  3. INSTALL REAR BUMPER ENERGY ABSORBER

    Tech Tips

    Perform this procedure only when replacement of the rear center ultrasonic sensor retainers is necessary.

    Click here

  4. INSTALL NO. 3 LUGGAGE ROOM WIRE

    Tech Tips

    Perform this procedure only when replacement of the rear center ultrasonic sensor retainers is necessary.

    Click here

  5. INSTALL NO. 1 ULTRASONIC SENSOR (for Corner Sensor)

    Tech Tips

    Use the same procedure for the RH side and LH side.


    1. When replacing only the No. 1 ultrasonic sensor:


      1. Engage the 2 claws to install the No. 1 ultrasonic sensor.

    2. Connect the connector.

  6. INSTALL NO. 1 ULTRASONIC SENSOR (for Back Sensor)

    Tech Tips

    Use the same procedure for the RH side and LH side.


    1. When replacing only the No. 1 ultrasonic sensor:


      1. Engage the 2 claws to install the No. 1 ultrasonic sensor.

    2. Connect the connector.

  7. INSTALL REAR BUMPER ASSEMBLY

    Click here