AUDIO AND VISUAL SYSTEM Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.


WIRING DIAGRAM

A002CBHE08

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be necessary. Refer to Precaution for Audio and Visual System.

Click here

PROCEDURE


  1. CHECK SPEAKER (OPERATION CHECK)


    1. A0028M8

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to

      Front No. 1 speaker assembly or front No. 2 speaker assembly

      (w/o Manual (SOS) Switch)

      		 A

      Front No. 1 speaker assembly or front No. 2 speaker assembly

      (w/ Manual (SOS) Switch)

      		 B
      Rear speaker assembly C

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the F69 radio and display receiver assembly connector.

    2. Disconnect the H3 and I3 front No. 1 speaker assembly connectors.

    3. Disconnect the G1 and G5 front No. 2 speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F69-1 (FR+) - G1-4 (+) Always Below 1 Ω
      F69-5 (FR-) - G1-2 (-) Always Below 1 Ω
      F69-2 (FL+) - G5-4 (+) Always Below 1 Ω
      F69-6 (FL-) - G5-2 (-) Always Below 1 Ω
      H3-1 - G1-3 (+) Always Below 1 Ω
      H3-2 - G1-1 (-) Always Below 1 Ω
      I3-1 - G5-3 (+) Always Below 1 Ω
      I3-2 - G5-1 (-) Always Below 1 Ω
      F69-1 (FR+) or G1-4 (+) - Body ground Always 10 kΩ or higher
      F69-5 (FR-) or G1-2 (-) - Body ground Always 10 kΩ or higher
      F69-2 (FL+) or G5-4 (+) - Body ground Always 10 kΩ or higher
      F69-6 (FL-) or G5-2 (-) - Body ground Always 10 kΩ or higher
      H3-1 or G1-3 (+) - Body ground Always 10 kΩ or higher
      H3-2 or G1-1 (-) - Body ground Always 10 kΩ or higher
      I3-1 or G5-3 (+) - Body ground Always 10 kΩ or higher
      I3-2 or G5-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  4. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the F69 radio and display receiver assembly connector.

    2. Disconnect the G1 and G5 front No. 2 speaker assembly connectors.

    3. Disconnect the F140 telematics transceiver connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F69-1 (FR+) - F140-2 (SPI+) Always Below 1 Ω
      F69-5 (FR-) - F140-3 (SPI-) Always Below 1 Ω
      F140-5 (SPO+) - G1-4 (+) Always Below 1 Ω
      F140-6 (SPO-) - G1-2 (-) Always Below 1 Ω
      F69-2 (FL+) - G5-4 (+) Always Below 1 Ω
      F69-6 (FL-) - G5-2 (-) Always Below 1 Ω
      F69-1 (FR+) or F140-2 (SPI+) - Body ground Always 10 kΩ or higher
      F69-5 (FR-) or F140-3 (SPI-) - Body ground Always 10 kΩ or higher
      F140-5 (SPO+) or G1-4 (+) - Body ground Always 10 kΩ or higher
      F140-6 (SPO-) or G1-2 (-) - Body ground Always 10 kΩ or higher
      F69-2 (FL+) or G5-4 (+) - Body ground Always 10 kΩ or higher
      F69-6 (FL-) or G5-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the H3 and I3 front No. 1 speaker assembly connectors.

    2. Disconnect the G1 and G5 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H3-1 - G1-3 (+) Always Below 1 Ω
      H3-2 - G1-1 (-) Always Below 1 Ω
      I3-1 - G5-3 (+) Always Below 1 Ω
      I3-2 - G5-1 (-) Always Below 1 Ω
      H3-1 or G1-3 (+) - Body ground Always 10 kΩ or higher
      H3-2 or G1-1 (-) - Body ground Always 10 kΩ or higher
      I3-1 or G5-3 (+) - Body ground Always 10 kΩ or higher
      I3-2 or G5-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  8. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  9. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. A0027VKC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
      3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

  10. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the F70 radio and display receiver assembly connector.

    2. Disconnect the K4 and J4 rear speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F70-1 (RR+) - J4-1 Always Below 1 Ω
      F70-3 (RR-) - J4-2 Always Below 1 Ω
      F70-2 (RL+) - K4-1 Always Below 1 Ω
      F70-6 (RL-) - K4-2 Always Below 1 Ω
      F70-1 (RR+) or J4-1 - Body ground Always 10 kΩ or higher
      F70-3 (RR-) or J4-2 - Body ground Always 10 kΩ or higher
      F70-2 (RL+) or K4-1 - Body ground Always 10 kΩ or higher
      F70-6 (RL-) or K4-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here