PARKING BRAKE ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL PARKING BRAKE SHOE GUIDE PLATE


    1. A018HUB

      Install the parking brake shoe guide plate with the parking brake shoe guide plate set bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  2. APPLY HIGH TEMPERATURE GREASE


    1. A018HPZC01
      B003ZIE High Temperature Grease

      Apply high temperature grease to the areas of the parking brake plate which make contact with the shoes as shown in the illustration.

  3. INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    1. for Front Side:


      1. Install the parking brake shoe hold down spring pin.

    2. for Rear Side:


      1. Install the parking brake shoe hold down spring pin.

  4. INSTALL PARKING BRAKE SHOE LEVER


    1. A018IKIC01
      B003ZIE High Temperature Grease

      Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.

    2. Temporarily install the parking brake shoe lever to the No. 2 parking brake shoe assembly with a new parking brake shoe type C washer.

    3. A018I44

      Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.

      Standard Clearance
      Less than 0.35 mm (0.0138 in.)

      If the clearance is not as specified, replace the parking brake shoe shim with one of the correct size.

      Parking Brake Shoe Shim
      Part No. Shim Thickness
      90564-09184 0.3 mm (0.0118 in.)
      90564-09185 0.6 mm (0.0236 in.)
      90564-09186 0.9 mm (0.0354 in.)

    4. Select a parking brake shoe shim and install it and the parking brake shoe type C washer.

    5. A018GW8

      Using a pair of pliers, squeeze together the ends of the parking brake shoe type C washer.

    6. Check that the parking brake shoe lever moves smoothly.

  5. CONNECT PARKING BRAKE SHOE LEVER


    1. A018JDW

      Using needle-nose pliers, connect the parking brake shoe lever to the No. 3 parking brake cable assembly.

  6. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    1. Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.

  7. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.

  8. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A018JTOC02
      B004057 High Temperature Grease

      Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

    2. A018HUP

      Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

  9. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A018LQZ

      Install the No. 2 parking brake shoe assembly to the backing plate with the parking brake shoe hold down spring cup and parking brake shoe hold down compression spring.

  10. INSTALL PARKING BRAKE SHOE STRUT COMPRESSION SPRING


    1. Install the parking brake shoe strut compression spring.

  11. INSTALL PARKING BRAKE SHOE LEVER STRUT


    1. Install the parking brake shoe lever strut.

    2. A018HM7

      Install the No. 1 parking brake shoe assembly.

  12. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A018IFA

      Install the No. 1 parking brake shoe assembly to the backing plate with the parking brake shoe hold down spring cup and parking brake shoe hold down compression spring.

  13. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)

    Note

    Be sure to install each parking brake shoe return tension spring in the correct position and direction.


    1. for Front Side:


      1. Install the parking brake shoe return tension spring.

    2. for Rear Side:


      1. Install the parking brake shoe return tension spring.

  14. CHECK PARKING BRAKE INSTALLATION


    1. Check that each part is installed properly.

      A018IH0C01
      *A LH Side *B RH Side
      B003ZIE Front of the Vehicle - -

      Note

      There should be no oil or grease on the friction surfaces of the shoe linings or discs.

  15. INSTALL REAR DISC

    Click here

  16. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

  17. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  18. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL

    Click here

  19. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }