REAR SPEED SENSOR(for AWD) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

The rear speed sensor rotor is a component of the rear axle hub and bearing assembly. If the rear speed sensor rotor is malfunctioning, replace the rear axle hub and bearing assembly.

PROCEDURE


  1. INSTALL REAR SPEED SENSOR LH


    1. A0028ZLN01

      Install the rear speed sensor LH and sensor clamp to the rear axle carrier sub-assembly LH and rear trailing arm assembly LH with the 2 bolts.

      Torque:
      Bolt (A)
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Bolt (B)
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note


      • Prevent foreign matter from attaching to the rear speed sensor tip.

      • Firmly insert the rear speed sensor body into the rear axle carrier sub-assembly LH before tightening the bolt.

      • After installing the rear speed sensor LH to the rear axle carrier sub-assembly LH, make sure that there is no clearance between the rear speed sensor stay and rear axle carrier sub-assembly LH. Also make sure that no foreign matter is stuck between the parts.

      • Do not twist the rear speed sensor wire harness when installing it.

    2. Install the 2 sensor clamps to the rear upper control arm assembly LH with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    3. Install the sensor clamp to the rear suspension member sub-assembly with the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    4. Connect the rear speed sensor connector.

    5. w/ Height Control Sensor:


      1. Engage the wire harness clamp to the rear speed sensor LH.

  2. INSTALL REAR SPEED SENSOR RH


    1. A002AAEN01

      Install the rear speed sensor RH and sensor clamp to the rear axle carrier sub-assembly RH and rear trailing arm assembly RH with the 2 bolts.

      Torque:
      Bolt (A)
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Bolt (B)
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note


      • Prevent foreign matter from attaching to the rear speed sensor tip.

      • Firmly insert the rear speed sensor body into the rear axle carrier sub-assembly RH before tightening the bolt.

      • After installing the rear speed sensor RH to the rear axle carrier sub-assembly RH, make sure that there is no clearance between the rear speed sensor stay and rear axle carrier sub-assembly RH. Also make sure that no foreign matter is stuck between the parts.

      • Do not twist the rear speed sensor wire harness when installing it.

    2. Install the 2 sensor clamps to the rear upper control arm assembly RH with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    3. Install the sensor clamp to the rear suspension member sub-assembly with the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    4. Connect the rear speed sensor connector.

  3. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  5. CHECK FOR SPEED SENSOR SIGNAL

    Click here